0
A voltage of 380 volts is a three phase voltage. On a three phase four wire system, each phase leg to neutral (grounded) will give you 220 volts. This voltage is obtained by dividing the phase voltage by 1.73, as the phase legs are generated 120 degrees from each other. Square root of three is 1.73 divided into 380 equals 220 volts.
What else can I help you with?
How do you hook up a water heater with red black and white wires?
Sounds like it is a 220-240 Volt hot water heater. The black and red are connected to the 220 volts supply and the white is connected to Neutral. At the breaker panel red and black connect to the 2-pole 220 volt breaker and white goes to the neutral bus bar.
How many wires needed for 220 volts ac though emt?
Two wires are needed for 220 volts.
What is the Household wiring color code?
On a 110 volt circuit, Black is hot, White is neutral, Green or bare Copper is ground. . Connect Black to the gold screw, White to the silver screw, and bare copper ground to the Green ground screw on the receptacle. On a 220 Volt circuit Black & Red are both hot, each carrying 110 volts for a total of 220. White is Neutral and ground is Green or bare copper.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
What is the voltage in Philippines?
220 volts 60 Hz
How connect a transformer 380 volt 3 pH to 220 volt mono pH?
any one of the three line to neutral is 220 volts
What is voltage between earth and line?
In a typical residential situation there is 220 to 240 volts between the two hot wires that are typically red and black and 110 to 120 volts between neutral and either black or red. The voltage between neutral and earth should be zero.
If a sine wave has a peak value of 220 volts what is the route means square value?
If the Peak to neutral voltage is 220 volts, the root mean square voltage is 155.6 volts (sqrt(220)).
Is it safe to connect 380 volts 3 phase supply to 220 volts 3 phase supply?
No.
Why does 220 volt line put out 250 volts?
A 220 volt line may put out 250 volts because this specification features voltage that varies between 220 and 250 volts. In other countries, the electricity varies in voltage between 110-120 volts.
How do you hook up a water heater with red black and white wires?
Sounds like it is a 220-240 Volt hot water heater. The black and red are connected to the 220 volts supply and the white is connected to Neutral. At the breaker panel red and black connect to the 2-pole 220 volt breaker and white goes to the neutral bus bar.
How is 110 volts and 220 volts measured?
With a voltmeter Keep volt meter terminal on phase and neutral wire and it will show the exact volatage
How to wire an appliance that has black white red and green wires?
It is most likely that the appliance is 220-240 Volts. Check the rating plate. If so you need to connect to that type of service and to a breaker that will handle the load. The 220-240 Volts is connected between Red and Black, White is neutral and provides 110-120 Volts between it and Red or Black. The Green is the ground.
How do you add a neutral wire for 220 volts?
Standard wiring for 220 volts which is also referred to as 240 volts, commonly has four wires. One is red, one is black, one is white and one is a bare copper wire. The red and black wire carry 120 volts each, the white wire in usually your neutral which hooks up to your ground along with the bare wire.
How do you install a 220 plug?
You need two hot legs of 110 volts to make 220. While each led is 110 volts to neutral, between the two hot legs you have 220v. You should have two different hot legs of 110, a neutral and a ground to meet code now a days.
On a 220 volt circuit where the white wire is common how many volts would the red wire be?
In a 220 volt circuit with a common white wire, the red wire would also carry 220 volts. The white wire is the neutral wire that completes the circuit and does not have a voltage potential, while the red wire is one of the hot wires that carries the full voltage of the circuit.
How do you get a 220 volt single phase from 380 volt 3phase synchrounos generator?
220 volt single phase from 480 volt 3 phase that one wire taken one phase and second wire connected in earth point. we get 220 v The above answer is incorrect, one phase from a three phase 480 volt system will give you 277 volts to ground. You must use a transformer to get the voltage you need.
