It's one phase of a 600V system. Or so I've heard the electrician say. I'm a plumber, don't ask me.
Wiki User
∙ 12y agoA regulator loses some voltage in regulating its output, known as the dropout voltage. So the input voltage must be at least the output volts plus the dropout volts. If the input voltage is too low, the output will drop out of regulation.
The causes of the electrical explosions is if the voltage of the electricity come down below 110 volts or become higher than 120 volts, it will explodes so you have to use an transformer into it.
The reverse breakdown voltage of the 1N4007 diode is 1000 volts.
4,160,000 volts
12 volts
208 is a three phase wye connection voltage. To obtain the each individual coil voltage the 208 is divided by 1.73 which equals to 120 volts. Hence you have 3 phase 208 voltage on the phase legs and 120 volts to the wye point which is grounded. This same formula is used on any 3 phase system. 600/347, 480/277, 208/120.
The voltage of 277 volts is the wye of a three phase 480 volt system. Just as the voltage of 347 is the wye voltage of a three phase 600 volt system. To obtain these voltages for any three phase system, take the three phase voltage and divide it by 1.73. 480/1.73 = 277 volts, 600/1.73 = 347 volts.
Yes there is single phase for 600 volts. It is used for lighting. You need a transformer which gives you 600 volts plus a neutral. The voltage for the one phase to neutral is 347.
The process of obtaining 220 volts from 380 volts is quite simple. 380 volts is a three phase four wire system voltage. The 220 volts is obtained by taking the sq. root of 3 which equals 1.73 and dividing it into the phase voltage. 380/1.73 = 220 volts. This holds true with any three phase four wire voltage system. 208/1.73 = 120 volts, 415/1.73 = 230 volts, 480/1.73 = 277 volts and 600/1.73 = 347 volts. This lower voltage is present on any of the three phase legs of the three phase system to the neutral which is grounded on a wye connection.
The star point or wye voltage of a 480 volt three phase four wire system is 277 volts. The 480 voltage is divided by the sq root of 3 (for 3 phases). The sq root of 3 is 1.73. 480 volts/1.73 = 277 volts. The same formula is used on all three phase four wire systems. 208 volts /1.73 = 120 volts, 416 volts /1.73 = 240 volts, 600 volts / 1.73 = 347 volts.
In the UK the mains voltage is 240 volts
220 volts, 110 volts, 440 volts, 400 volts, AC or DC voltage. High voltage like - 220 KV, 400 KV, etc
15 voltsThe result would only be 15 volts if they were connected in series. If in parallel, a 10v and a 5v battery would probably come out with a voltage of either 10 volts or 7.5 volts, there's no way to tell for sure though.
Low voltage by definition means any voltage from 31 to 750 volts inclusive.
If you are talking about normal house hold voltage it would depend in which country you live in. For North America it would be 120/240 volts. For Europe and Eastern countries it would be 240 volts. Industrial voltages vary from country to country. These normal voltages range from 120, 277, 240, 347, 415, 480, to 600 volts.
These voltages are both wye connection three phase voltages. The voltage difference comes from the primary three phase voltage supplies. 277 volts is obtained from 277 x 1.73 = 480 and 240 volts is obtained from 240 x 1.73 = 415. 480/277 volts is a common three phase American voltage. 415/240 volts is a European voltage. In Canada a common three phase voltage is 347/600. The 240 volts could also be a single phase voltage in North America derived from a split phase secondary on a distribution transformer that supplies 120/240 volts to homes.
The voltage is ~120 Volts.