0
It depends upon the length of the circuit, but for 50 feet or less a 10 gauge wire should be fine. A short length (15 feet), you could use 12 gauge. If you double the length to 100 feet, you should use 8 gauge. A rule of thumb is to drop down a gauge for every length that is doubled.
There are wire size charts available on the internet. Some can be conservative such as recommending #8 for 50 ft or less at 30 amps. It is better to be conservative than to run too much amperage on a smaller wire that can cause a fire.
As a general rule, 12ga wire can be used in house circuits for 20amps or less. 16ga wire can be used for 15 amps or less such as lighting circuits. That is considering lengths of less than 100 feet.
Add your answer:
Earn +20 pts
What size amp circuit breaker should be used for 110 outlet?
The size breaker you use is determined by the size wire used in the circuit. If you use AWG #12/2 wire then use a 20 amp breaker. If you use AWG # 14/2 then use a 15 amp breaker.
Is a 15 amp 2 wire outlet wired with copper wire?
Yes it is wired with copper 2 wire is also known as 14/2 wire is use for switches,outlets,lights. and a 15a outlet should only be on a 15a breaker the main power feed to your meter to your panel is aluminum and can take more of a load than copper. In the US, 15 amp receptacles can be installed on 20 amp circuits if there is more than one receptacle on that circuit. Copper wire can carry a larger load than aluminum wire of the same size.
What gauge wire do you run between a 30 amp breaker and an outlet?
10 AWG.
What wire size needed for 150 feet run on 30 amp?
This is a voltage drop question. To answer this question a voltage must be stated.
What gage wire is needed for a 35 amp ac?
Use 8 gauge wire.
Can you change a 120v 15 amp outlet into a 30 amp?
No, it is not safe or legal to change a 120V 15 amp outlet into a 30 amp outlet without rewiring and ensuring that the electrical circuit can handle the increased load. You should consult with a licensed electrician to properly install a 30 amp outlet where needed.
What size amp circuit breaker should be used for 110 outlet?
The size breaker you use is determined by the size wire used in the circuit. If you use AWG #12/2 wire then use a 20 amp breaker. If you use AWG # 14/2 then use a 15 amp breaker.
How do you choose the right fuse for the job?
The correct size fuse needed is based on the size wire used in the circuit. The size wire needed is based on the load that will be applied to the circuit. 1. AWG 14/2 wire = 15 amp fuse 2. AWG 12/2 wire = 20 amp fuse 3. AWG 10/2 wire = 30 amp fuse 4. AWG 8/2 wire = 40 amp fuse
What wire size needed for 120 volt 3000 watt load?
AWG # 10 wire on 30 amp circuit.
What size wire is needed for 240v 3.5 amp system?
16 mm to 18 mm
What size wire is needed to run a 50' 20 amp curcuit?
12 gauge or bigger.
What is the wire size needed to feed a 400 amp service with parallel copper?
It depends on the length of the run
What size ground wire is needed for 20 amp?
For a 20 amp circuit, a 12-gauge copper ground wire is typically recommended. This wire size can safely handle the current and provide proper grounding for the circuit.
What type of outlet needed for a elect range 30 amp or 50 amp?
30
What size breaker does it take to run a outdoor well?
Normally AWG #10 wire on a 30 amp breaker but it really depends on the size of the pump. The pump manufacture will specify the size wire and size breaker needed.
What is the amp size of a 8 wire?
The amp size of a wire is determined by its gauge, not the number of wires. An 8-gauge wire is typically rated for around 40-60 amps, depending on the type and insulation of the wire.
Is a 15 amp 2 wire outlet wired with copper wire?
Yes it is wired with copper 2 wire is also known as 14/2 wire is use for switches,outlets,lights. and a 15a outlet should only be on a 15a breaker the main power feed to your meter to your panel is aluminum and can take more of a load than copper. In the US, 15 amp receptacles can be installed on 20 amp circuits if there is more than one receptacle on that circuit. Copper wire can carry a larger load than aluminum wire of the same size.
