0
A fixture or device that holds a light in place by means of some sort of socket, that is connected to a power source.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is a pin based fluorescent light fixture?
A pin based fluorescent light fixture is the type of fixture that takes fluorescent tubes. On each end of the fluorescent tubes there are contact pins. These pins are used to hold the tube in the fixture and to supply the voltage to the tube from the fixture's ballast.
What happens if a light fixture overheats?
it will explode
What do you do with extra wires to a light fixture?
Extra wires to a light fixture are dangerous. It can cause electrical shock when having contact to people therefore it must be guarded to avoid physical contact.
How do you connect an ON-OFF switch to control the light?
To control a light with a switch, the switch has to be connected in series with the light fixture.
Can a hps light fixture be plugged in to a regular outlet?
If the ballast of the HPS fixture has a 120 volt tap then, yes it can be plugged into a 120 volt receptacle.
How do you spell fancy light fixture?
The correct spelling for a fancy light fixture is "chandelier."
How do you wire a 220 volts light?
The light is wired the same as any voltage fixture. Bring the source voltage to the fixture and connect it to the two fixture wires. If you want to control the off-on of the fixture take the source voltage to a switch first and then out of the switch to the light fixture.
How do you remove the dome from a light fixture?
Take the nut off at the bottom of the light fixture by unscrewing it.
Can you connect a wall switch and a light fixture to an existing light fixture?
Yes, you can connect a wall switch to an existing light fixture by running a new electrical wire from the switch to the fixture. This allows you to control the light fixture independently of the existing fixture. It is recommended to consult a licensed electrician to ensure proper wiring and installation for safety.
How do you release dome from light fixture in ceiling fan?
Disconnect the fixture wires and remove the central mounting nut to release the dome from the light fixture in a ceiling fan.
What is a light fixture that hangs from the ceiling?
A chandelier is a decorative light fixture that hangs from the ceiling and typically has multiple arms with light bulbs.
How do you remove the tail light lens from a 1989 Chevy Celebrity?
The tail light lens on a 1989 Chevy Celebrity is part of the tail light fixture and cannot be conveniently removed. If you want to change a light bulb you have to remove the tail light fixture from the car. To remove the tail light fixture: 1. In the trunk next to the quarter panel are three nuts, remove the center nut. It should be in the center of the tail light fixture. 2. Pull the tail light fixture so that the stud comes out of the body, then pull outward to pull the tab out of the backup light fixture. 3. You can now take the appropriate socket out and replace the bulb. Reverse the steps to replace the light fixture.
What is a pin based fluorescent light fixture?
A pin based fluorescent light fixture is the type of fixture that takes fluorescent tubes. On each end of the fluorescent tubes there are contact pins. These pins are used to hold the tube in the fixture and to supply the voltage to the tube from the fixture's ballast.
Does a down light consume less electricity?
The fixture construction has nothing to do with the amount of energy that the fixture uses. It is the lamp in the fixture that draws the amperage. This amperage times the fixtures voltage is what gives you the fixtures wattage. W = A x V. Watts = Amps x Volts.
What is marble's light?
A marble light is a light fixture made of marble.
What is the cost of replacing a light fixture/fan unit?
A light fixture/fan unit can run anywhere from 50-200 dollars
How do you convert a swivel recessed light to accept the pendant light kit?
To convert a swivel recessed light to accept a pendant light kit, you will need to remove the existing recessed light fixture and install a pendant light fixture in its place. This typically involves disconnecting the wiring for the recessed light and attaching it to the pendant light fixture according to the manufacturer's instructions. You may also need to install a mounting bracket to support the pendant light fixture.
