There are three operating regions in transistor...(Transfer-Resistor)
1)cutoff region
2)Active region
3)Saturation region
Active region:
Cutoff region:
Saturation region:
Based on application the transistor is decided where to lie.
for example transistors are made to lie in active region to make it as amplifier.
when transistors are used as switch it is made to lie in saturation region(when switch is made as ON) and cut-off region(when switch is made as OFF).....
Thanks guys for reading this. please forgive me if there are any mistakes....
ANSWER: In actuality there is only one REGION The other regions are not operating regions but rather states. An operating region on a transistor is set up during design of an amplifier to transfer maximum undirstorted power to the load. This design is called BIAS
Q point is also called operating point.Q point is mainly adjusted in transistors to make it stable. i.e., to operate the transistor in safe mode. Depending up on the operating current and voltage Q point is adjusted. The Q point defines the operating condition of the transistor and the transistors which quiescent point is adjusted are denoted as Q1,Q2.........Qn
A fridge may or may not have a few transistors in it, these are electrical components that would probably be part of the control circuitry. Transistors used to be very common components of most electrical appliances. The cooling process of the fridge has nothing to do with transistors and is handled by a compressor and a heat exchange pump
6
I am not to sure about Static Ram but in CMOS RAM, 1GB of RAM would contain about 137438953472 transistors because 1 bit of CMOS RAM contains 16 Transistors, 8 bits in a byte and 1073741824 bytes in a gigabyte. I am 100% sure about this and these are just estimations. Static RAM uses about 6 times as many transistors as dynamic RAM for the same amount of storage. Dynamic RAM uses 1 or 2 transistors per bit in typical implementations. Add to this transistors for address decode, bus interface, etc.
If the integrated circuit in some kind of device has 5,000 transistors on it, then before integrated circuits were available, the same function might have been performed by 100 individual transistors. And before transistors were available, the same function might have been performed by 30 vacuum tubes, a fan and air system to keep them cool, and a large power system to operate the tubes and the cooler.
We bias transistors in order to determine the modes of operation ( that is whether the transistor is operating in the active cut off or the saturation regions).
operating region of the transistor is the area of the voltage and an electronic configuration in which a transistor can work with its full efficiency. In that operating region transistor can be used easily what above said by harsh is correct...the following may help u further... Based on application the transistor is decided where to lie. for example transistors are made to lie in active region to make it as amplifier. when transistors are used as switch it is made to lie in saturation region(when switch is made as ON) and cut-off region(when switch is made as OFF).....
explain the different components of operating system in details
Q point is also called operating point.Q point is mainly adjusted in transistors to make it stable. i.e., to operate the transistor in safe mode. Depending up on the operating current and voltage Q point is adjusted. The Q point defines the operating condition of the transistor and the transistors which quiescent point is adjusted are denoted as Q1,Q2.........Qn
1. What are the two kinds of installation of an operating system? Explain Briefly.
You need to explain what you mean by perceptual regions. What is that?
Q point is also called operating point.Q point is mainly adjusted in transistors to make it stable. i.e., to operate the transistor in safe mode. Depending up on the operating current and voltage Q point is adjusted. The Q point defines the operating condition of the transistor and the transistors which quiescent point is adjusted are denoted as Q1,Q2.........Qn
The element highly toxic and used in transistors is arsenic. It is commonly found in old radios and semiconductor components due to its semiconductor properties in creating p-type regions.
An operating system which is run on server but is assessed/interacted with by a terminal.
what are hierachies are used for process in operating systems
All of the transistors must be biased in their operating range to work correctly.
Core i5-655K features an unlocked multiplier. FSB has been replaced with DMI. Transistors: 382 million; Die size: 81 mm²; Transistors: 177 million