24 DSO equal T1
On a schematic for an electronic circuit it usually means a transformer. T1 is the 1st transformer, T2 is the second etc. Some ferrite core wire wound inductors with more than one winding may be designated as T1.
On the load side of the contactor. T1,T2,T3.
it is a combination of two transistors connected in series. the emitter of transistor t1 is connected to the base of transistor t2 . now the total circuit acts as a single transistor. this combination will gives high gain, as the gain is multiplied.
A: It depends on the current load but the Small terminal is the gate that will allow the triac to conduct. However the gate cannot be used to shut it off, The only way to shut it off is t reduce the current below the holding current or revering the polarity for the triac when conducting
24 DSO equal T1
DS3 is 44.7 Mbps and a T1 is 1.55 Mbps. So 1 DS3 = 28 T1s http://www.dslbroker.com/ds3.html
A DS3 has 28 T1's http://techblog.intelletrace.com/what-is-a-ds3-hub/
A T1 is 1.5Mbps. A T3 or DS3 is 45 Mbps. THere are 28 T1's in a DS3. T1 Internet Services http://www.intelletrace.com/internet-services/T1-Internet-Service.html DS3 or T3 Internet Services http://www.intelletrace.com/internet-services/DS3-Internet-Services.html
An OC3 breaks down to three DS3's. A DS3 Breaks down to 28 T1's. Therefore there are 84 T1's on an OC3. If you go one step further there are 672 DS0's on a DS3 or 2016 DS0's on an OC3. a DS0 is a 64k Channel equal to a single POTS line. http://techblog.intelletrace.com/what-is-a-ds3-hub/
A T1 is copper, and OC3 is fiber optic, so there is no way to make a T1 into OC3. Speed on a T1 is 1.544 Mbps, and speed on the OC3 is 155.52 Mbps, so in rounding, you need 100 T1 lines to equal the speed of an OC3.
This question actually is unanswerable. A DS3 or T3 has 28 DS1 or T1's. A E3 has 16 E1's There is no comparison between the two. A DS3 moves data at 45Mbps an E3 is 34 Mbps. they can not directly connect together. This includes their subrates. An E1 can not connect directly to a T1 without a converter.
T3 is another word for the hormone triiodothyronine which is produced by the thyroid gland
T3 is the same as DS3 DS3 is a 44.736 Mbps Data Circuit or if channelized 28 T1's. T-carriers are made of multiple plain old telephone lines, but with many more channels (wires for transmission).
T3 is the same as DS3 DS3 is a 44.736 Mbps Data Circuit or if channelized 28 T1's. T-carriers are made of multiple plain old telephone lines, but with many more channels (wires for transmission).
There is no direct mapping of E1 to DS3. The only way to connect the two is using an MPLS network. A DS3 is 45Mbps. An E1 is 2Mbps. The bandwidth of 22.5 E1's can traverse a DS3. In order to directly connect an E1 as would a T1 to a DS3 you would need an E3 An E3 is 34 Mbps and 16 E1's could connect to it.
An OC12 is the equivalent of 4 OC3's or 12 DS3's. A DS3 Breaks down to 28 T1's. Therefore there are 336 T1's on an OC3. If you go one step further there are 672 DS0's on a DS3 or 8064 DS0's on an OC12. a DS0 is a 64k Channel equal to a single POTS line. http://techblog.intelletrace.com/what-is-a-ds3-hub/