0
Add your answer:
Earn +20 pts
Do you need to change the wire size going from 100 amp service to 150 amp service?
Yes, the wire size has to be increased. The existing 100 amp service will now probably have a #3 conductor with an insulation factor of 75 or 90 degrees C which is rated for 100 and 105 amps respectively. Increasing to a 150 amp service will use a #1/0 wire size. If you are thinking of an upgrade, skip the 150 amp service and go to a 200 amp panel. New homes are installing 200 amp 42 circuit panels. The extra cost is only reflected in the materials as the labour costs will be the same regardless whether a 150 amp or a 200 amp panel is installed. The wire size for a 200 amp panel is #3/0. With an insulation factor of 75 or 90 degrees C the rating is 200 or 210 amps respectively.
What size Aluminum wire is used for ground in breaker box?
For a 100 Amp breaker panel it would be 2 AWG. For 150 Amps it would require 2/0 (2 ought) aluminum wire.
What is largest wire you can use in 150 amp breaker panel?
A 1/0 copper conductor with an insulation factor of 75 and 90 degrees C is rated at 150 and 155 amps respectively. Any size larger that 1/0 can be used but no conductor smaller that 1/0 will be approved for connection.
What size aluminum wire for 100 amps undergroundservice 60 feet from meter?
A 3/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 150 amps for 150 feet on a 240 volt system. This size will allow the conductor to be loaded to 120 amps. 150 x 80% = 120 Conductors are only allowed to be loaded to 80% or their rated capacity. If you need the full 150 amps then you would need to use a wire with a rating of 190 amps. 190 x 80% = 152 amps A 4/0 aluminum conductor will limit the voltage drop to 3% or less when supplying 190 amps for 150 feet on a 240 volt system.
How many watts will a 150 watt High Pressure sodium light with a capacitor draw?
It will draw 150 watts. The capacitor is there only to increase the voltage enough to "excite" the free electrons in the gas to ignite.
How many circuits are on a 150 amp panel?
As many as needed; panel capacities are different from each other in amps and space. there should be a sticker on the door of the panel that tells of how many breakers can be installed in that panel. regarding the amps, a load calculation can be made to determine the full load used on such a panel.
How do you combine two or more circuits to achieve greater amperage ie. combine two 20 amp circuits to achieve a 40 amp circuit?
If you mean "combining circuits" as in connecting two or more circuits in parallel, this is only allowed by the National Electrical Code when the wires are at least size 1/0 (about 150 amps) You are not allowed to parallel conductors smaller than 1/0 If you meant something else, you need to clarify the question
What would cause the instrument panel on a 1997 Ford F-150 not to work?
What would cause the instrument panel on a 1997 ford pickup 150 not to work?
Remove rear door panel F-150?
sas
Can you add a 220 line to your 150 amp panel?
Adding a 220V line to a 150 amp panel is feasible, but you must ensure the panel can accommodate additional amperage. Consult an electrician to confirm if the panel has available space and if it meets the necessary electrical code requirements for the new line.
Which fuse in the fuse panel is for the lighter in 2001 ford F-150?
which fuse on the ford 150 2002 is for the lighter
How much is a solar panel?
The cost of a solar panel can vary based on factors like size, quality, and manufacturer. On average, a typical residential solar panel can cost between $150 to $350 per panel. However, the total cost of a solar panel system will depend on how many panels are needed for your energy requirements.
1994 ford econoline e150 engine performance circuits?
table for a 1994 ford 150 conversion van
How do you remove the inside door panel on a 2001 Ford F-150?
How do you remove the inside door panel of a 2001 ford f150.
How do you find out how big your main breaker box is?
You can determine the size of your main breaker box by looking at the number of circuits it can handle. A typical residential main breaker box is usually 100 amps, 150 amps, or 200 amps. You can also check the label on your breaker box or consult with an electrician for assistance.
How do you remove driver door panel on a 2010 ford F 150?
remove interior door panle diver sidef-150
Where can you find a fuse panel diagram for a 1991 Ford E-150?
at autozone
