0
Add your answer:
Earn +20 pts
How many amps drawn a 110KW motor?
Watts = Volts times Amps. Therefore, if the voltage was 220 volts, the motor would draw 500 amps. If the voltage was 4,000 volts, the motor would draw 27.5 amps. The voltages for large powerful motors tend to be relatively high, for example in the 380 Volts to 11,500 Volts range.
How many amps should a 0.5 horsepower motor draw?
Depends on the voltage. If you are running off 120 VAC, a 0.5 horsepower motor would draw 3.1 A.
How many amps does a 30HP motor use hooked to 480v 3 pH 60Hz line?
The electrical code states that a 30 HP induction motor at 460 volts three phase will draw 40 amps. <<>> I = 33.34 AMPS IF EFF.= 95% AND P.F.= 85%
What is the cable size for motor 15kw 440 volts connection?
The current draw is about 27 amps. A motor feeder has to be 125% of the motors full load amperage. 27 x 125% = 33 amps. A #8 copper conductor with an insulation factor of 90 degrees C is rated at 40 amps.
How many amps does a 1 hp electric motor pull under a load?
T430.247 of the NEC shows that a 1 hp motor operating at full load on 115v will draw 16 amps, called Full Load Current (FLC). Conductors supplying this motor are required to be 125% of FLC which is 20 amps. Motor circuits are complicated things and do not follow the rules of other circuits. This motor, while drawing a maximum of 16 amps at full load and supplied with #12 AWG copper conductors can be protected by a breaker of 40 amps.
Will a 10 hp 220 volt motor draw large amounts of electricity?
A single phase 10 HP motor will draw aproximately 50 amps. A three phase 10 HP motor will draw aproximately 28 amps.
How many amps will a 24 volt dc motor draw if running at 12 volts?
Depends on how big the motor is. A stronger motor will draw more amps then a weaker or less efficient motor. For example a wiper motor draws far less then a starter motor.
Why does a slow motor create high amps?
Excessive resistance (drag), will cause motor to draw more amps (current flow) to operate.
How many amps does a 15 hp motor draw?
To answer this question the voltage of the motor must be stated.
How many amps drawn a 110KW motor?
Watts = Volts times Amps. Therefore, if the voltage was 220 volts, the motor would draw 500 amps. If the voltage was 4,000 volts, the motor would draw 27.5 amps. The voltages for large powerful motors tend to be relatively high, for example in the 380 Volts to 11,500 Volts range.
18kW motor will take how many amps?
To calculate the amps drawn by an 18kW motor, you can use the formula: Amps = Power (Watts) / Voltage (Volts). Assuming a standard voltage of 120V, the motor would draw approximately 150Amps. Note that actual amps will depend on the specific voltage of the motor.
How many amps for 1hp 3phase?
For a 1hp 3-phase motor, the current draw will depend on the voltage supply. Typically, at 230V, a 1hp 3-phase motor will draw around 3.6 amps. However, this value may vary based on the motor efficiency and power factor.
How many amps does a five horse power motor draw?
It depends on the voltage-- I think at 110v it's 4 amps per hp
How many amps should a 0.5 horsepower motor draw?
Depends on the voltage. If you are running off 120 VAC, a 0.5 horsepower motor would draw 3.1 A.
How many amps should a starter draw?
A typical starter motor draws around 50 to 150 amps while cranking an engine. If the current draw is significantly higher or lower, it may indicate a problem with the starter motor or the electrical system.
How many amps does a 5 hp 208 volt 3 phase motor draw?
read the name plate on the motor
What is the amps for a 2.5hp 240v cont motor draw.?
For a 2.5hp 240v continuous motor, the current draw would be around 10 amps. This can vary slightly depending on the motor's efficiency and other factors, but 10 amps is a good estimate to use for this motor.
