0
Plug a lamp into a working socket of an outlet to ensure the lamp works. Then turn off the switch and plug lamp into all outlet sockets, top and bottom outlets until the lamp doesn't light. Then turn on the switch and the lamp should light. Often a switch in a bedroom is only connected to one socket in a duplex outlet. It is possible to remove a jumper in an outlet to isolate the sockets for just this purpose. Often an electrician will install the outlet upside down (The third prong pointing up, to identify the outlet.
Add your answer:
Earn +20 pts
Why is there no power to outlet when light switch is turned off?
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
Is the switched portion of an outlet mounted toward the top or the bottom?
There is no switch on an outlet. You can mount an outlet with the ground up or down. Most electricians I know mount the ground down as I do.
How do you disconnect a light switch and outlet that are tied together?
If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.
What is unidirectional current controller device?
A unidirectional current controller device is a type of electrical on/off switch. In order for an item to work that is plugged into a particular outlet, the switch must be in the on position. It is like having lamps plugged into outlets that are controlled by only one switch.
What are the two wires for?
On what? IS this an outlet or a switch?
Does an outlet controlled by a light switch still pull energy when the light switch is off?
No.
Can you wire a switch downstream from an outlet?
Yes, you can wire a switch downstream from an outlet by connecting the switch to the hot wire (black) from the outlet. The hot wire would then be interrupted by the switch before continuing to the outlet, allowing you to control the power to the outlet with the switch. Always ensure to turn off the power before working on any electrical components.
Why is there no power to outlet when light switch is turned off?
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
How do you wire a gfci outlet with fan switch?
To wire a GFCI outlet with a fan switch, connect the incoming power source to the LINE terminals on the GFCI outlet. Then, connect the load side of the GFCI outlet to the switch. From the switch, connect the power supply for the fan to complete the circuit. Make sure to follow the manufacturer's instructions and all local electrical codes for safety and proper installation.
Is the switched portion of an outlet mounted toward the top or the bottom?
There is no switch on an outlet. You can mount an outlet with the ground up or down. Most electricians I know mount the ground down as I do.
How do you run a light with a switch from a existing outlet with out controlling the out let with the switch?
Break off the tab that jumps between the wire mounting screws on the side of the receptacle. This turns one receptacle into 2 seperately controlled parts--one is always hot and the other is controlled by the switch (the one with the lamp plugged in).
Why won't a three way lamp switch work on all three settings when used in a outlet controlled by a wall switch?
A three-way lamp switch requires a dedicated three-way bulb and socket to function on all three settings. If used in an outlet controlled by a wall switch, the voltage may not be appropriate for all settings to operate correctly. Additionally, the wiring configuration in the wall switch setup may not be compatible with the three-way lamp switch.
How do you wire 2 new lights with on-off switches using wires coming from an existing outlet?
You can attach/splice into the power feed to outlet (ways of doing this can vary with how the outlet is wired but make sure that all or part of the outlet isn't controlled by an existing switch). You can then take the hot, neutral and ground to a light fixture or to the first switch, then to the second switch. It is normally easier to do this project by taking power to the light (s) first, with 2 wire drops to the switches, from basement or attic.
How do you disconnect a light switch and outlet that are tied together?
If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.
Can it be dangerous to wire one outlet of a double outlet to a switch?
No, that is not unsafe.
Is there a switch that can make current rapidly stop and go?
Yes, it is an electronic switch know as a triggered SCR (Silicon Controlled Rectifier)
Why does the light switch not work to an existing electrical outlet?
Could be a loose connection somewhere, or a bad switch, or a bad outlet.
