0
You would need to take the "input" wire for the shunt trip breaker to an electrical switch (not alarm initiating switch, which are DC voltage rated) within the Automan unit and connect to the "Common" connection and the "return", the wire to the actual shunt circuit of the breaker, from the "Normally Open" connection of the switch.
When the unit activates, the switch will be placed into "Closed" position, therefore completing the circuit and activating the shunt coil.
What else can I help you with?
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
Can you take a 14 awg wire and hook it to a 12 awg wire?
Yes as long as the breaker feeding the circuit is protected with a 15 amp breaker. The code states that the over current device can be no smaller than that of the smallest current carrying conductor. That will be the #14 wire with a capacity of 15 amps.
What gauge wire is required to hook up an electric kitchen stove?
Normally a new kitchen stove will require a 50 amp breaker wired with AWG # 6/3 with ground wire.
How do you hook up a water heater with red black and white wires?
Sounds like it is a 220-240 Volt hot water heater. The black and red are connected to the 220 volts supply and the white is connected to Neutral. At the breaker panel red and black connect to the 2-pole 220 volt breaker and white goes to the neutral bus bar.
Can I wire nut two black wires together and hook 1 to a breaker?
Not according to the electrical code. It requires each separate circuit to be fed individually from its own breaker. If allowed it would reduce the total capacity of each circuit from one amp per outlet to a half amp per outlet if the circuit was fully loaded.The work around in situations like this is to use a tandem breaker which gives you the capacity of two complete circuits and only using one breaker slot in the distribution panel board.
How do you hook up a 40 amp breaker panel?
To hook up a 40 amp breaker panel, first turn off the main power source. Then, connect the wires from the circuit breaker to the panel's bus bar, making sure to follow the manufacturer's instructions. Lastly, turn the main power back on and test the circuit to ensure it is working properly.
How do I safely hook up a generator to my breaker box?
To safely hook up a generator to your breaker box, you should use a transfer switch installed by a qualified electrician. This switch ensures that power from the generator is isolated from the main grid, preventing backfeeding and protecting against electrical hazards.
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
How do I safely and correctly hook up a generator to a breaker box?
To safely and correctly hook up a generator to a breaker box, you should use a transfer switch installed by a qualified electrician. This switch ensures that power from the generator is isolated from the main grid, preventing backfeeding and protecting against electrical hazards. Never directly connect a generator to a breaker box without a transfer switch.
How do you hook up the vacuum system if you have a Hayward 210T filter?
The vac system has to hook up the the skimmer not the Hayward filter. k
Can you hook a PS3 to a 360 and system link?
no
Can you hook up a 4800 watt construction heater to a 40 amp stove outlet?
If you are using typical residential voltages ( 120v/240v) a 40 amp breaker is plenty big enough. You could even use a twenty amp breaker.
Can I hook my game system into my VCR, or do I have to unplug it and hook it into my TV?
You can always hook it up to a VCR with composite cables and it'll work just fine.
Can you use 10 2 to hook up breaker box?
No, using a 10-2 wire for a breaker box is not recommended. For a breaker box, it is typically required to use a minimum of 12-gauge wire with a ground wire. It is important to follow local electrical codes and consult with a professional electrician for proper installation.
Can you hook up portable dishwasher to the washer?
yes only if it is on its own breaker. the dishwasher also must be at least 20 amps and the washing machine as well. if the dishwasher is on its own breaker and they both have the same voltage than yes.
How do you hook up video games on your PC?
Hook up a USB cable from the system to your hard drive or laptop.
What is the purpose of a hook?
A hook is a function that allows you to add custom functionality to a software system without modifying its core code. It helps developers extend or modify the behavior of the system by "hooking into" specific points in the code where the hook is called.
