0
Still curious? Ask our experts.
Chat with our AI personalities
Fran
Vivi
ProfessorAdd your answer:
Earn +20 pts
Does a GE 24 circuit A Series panelboard 3 phase accept bolt on breakers?
Type AE and AQ accept bolt-on breakers, type AL accepts plug-in breakers.
Is it possible to convert 220 v wiring to two 110 v wiring?
You will need a 220 volt primary isolation transformer with a split, center taped, secondary 220 volt winding.-------------------Answer for USAIf you live in the United States and your 220v circuit is a 2-pole circuit, you replace the 2-pole breaker with 2 individual 110v breakers and **PRESTO** you are now ready to run 2 individual 110v circuits.If you wish to use existing wiring, and you have 3 wires plus ground, you have all you need. These 2 circuits can share the same neutral without any electrical danger.Before you do any work yourselfon circuits, equipment or appliances,ensure the circuit is, in fact, OFF.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What does a 3 pole circuit breaker do?
It provides power to 3 conductors simultaneously, and more importantly, disconnects all three conductors simultaneously in case of a fault. A three pole breaker is used with a three phase power system.
What size breakers for a hobart P660 mixer with 8.6amp pull and 3 phase?
The size-breakers for a Hobart P660 mixer with 8.6amp pull and 3 phase is the 23.43-inch size breakers.
What might cause low voltage at one outlet on a multioutlet circuit?
its an overload on the circuit breaker the 3 outlets are on.. many times groups of outlets are on different circuit breakers.. even though they are in the same room... especially if some are on a gfi outlet
What difference between using 4poles circuit breaker and using 3 single pole breakers?
3 pole would be for 3 phase, 4 pole would be 3 phase & neutral
What are the advantages and disadvantages of a double pole circuit?
A double pole switch can be used in either a 240V application where you'll need to disconnect 2 "hot" lines, or it is useful when switching a light from 3 different switches. Disadvantage? I suppose it could be a little confusing to face all those contacts on a double pole switch.
Does a GE 24 circuit A Series panelboard 3 phase accept bolt on breakers?
Type AE and AQ accept bolt-on breakers, type AL accepts plug-in breakers.
How do you change one breaker on a 3 wire that feeds two regular circuit breakers to a single arc fault circuit breaker - or do you have to change both breakers to arc fault so each has a neutral?
In order to properly convert a circuit to an arc fault circuit breaker, both the hot and neutral wires must be connected to the arc fault breaker. This means that you would need to change both breakers to arc fault breakers, as each would require its own connection to the neutral wire to function effectively and meet safety standards.
Why does my heating and air conditioner in my house have 3 double pole breakers - a 30 40 and 50?
In North America a two pole breaker usually represents a load that requires a 240 volt source. Larger current load appliances use 240 volts to reduce the feeder size and there by reduces the cost factor when wiring a building. Two pole 15 amp breakers are used for kitchen counter split receptacles.Two pole 20 amp breakers can be used for baseboard heating and hot water tanks.Two pole 30 amp breakers can be used for clothes dryers and some heating units.Two pole 40 amp breakers can be used for electric ranges.Two pole 50 amp breakers are not common in home wiring circuits. It might be used for an electric furnace or some other high current device.
What happens when two circuit breakers are parallel?
There are 3 cases in C.B. paralleling: 1. Both Circuit breakers of same current ratings with same time settings. 2. Both circuit breakers of different current ratings 3. Both Circuit breakers of same current ratings with different time settings. Case1: Any of the C.B.trips (depending on CT characteristics as no two CTs' can have same characteristics) Case 2. The one with lower current ratings would trip first. Case 3: The one with lower time settings would trip earlier.
How can a 3-way switch be used as a single pole in a circuit?
A 3-way switch can be used as a single pole in a circuit by connecting the common terminal to either one of the traveler terminals. This effectively turns the 3-way switch into a regular on/off switch, allowing it to control the flow of electricity in the circuit like a single pole switch would.
Rating of a 3 pole circuit breaker is the same for each conductor?
Yes, the rating of a 3 pole circuit breaker is the same for each conductor that is connected to it. A three pole breaker rated at 30 amps will have 3 #10 wires from it that connect to the load.
What protects circuits from current overloads?
Electrical circuits are protected by: 1) Fuses 2) Circuit Breakers and/or 3) Fusable links
Is a 3 phase cable one circuit?
If it is powering a single 3 phase device and is protected by a single throw 3 pole breaker or disconnect, yes. If all three hots share one neutral, and supply different devices or circuits, breakers should be able to trip independently but would still have to disconnect all three phases together.
Is it possible to convert 220 v wiring to two 110 v wiring?
You will need a 220 volt primary isolation transformer with a split, center taped, secondary 220 volt winding.-------------------Answer for USAIf you live in the United States and your 220v circuit is a 2-pole circuit, you replace the 2-pole breaker with 2 individual 110v breakers and **PRESTO** you are now ready to run 2 individual 110v circuits.If you wish to use existing wiring, and you have 3 wires plus ground, you have all you need. These 2 circuits can share the same neutral without any electrical danger.Before you do any work yourselfon circuits, equipment or appliances,ensure the circuit is, in fact, OFF.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How to eliminate a 3-way switch in a circuit?
To eliminate a 3-way switch in a circuit, you can rewire the circuit to remove the switch and connect the wires directly. This will convert the circuit to a standard single-pole switch setup. Make sure to turn off the power before working on the circuit and follow proper safety precautions.
