0
Add your answer:
Earn +20 pts
How can I disable dhcp on Windows 2000 server?
Either disable the dhcp scope, or remove the service.
Using the control panel to install dhcp configure and activate dhcp with a scope of?
DHCP has to be configured by using the DHCP snap-in MMC console. This is under the Administrative Tools once DHCP has been installed. In Windows Server 2008 you add the Role, so it isn't installed via the Control Panel at all. For configuring the scope, you need to specify the address ranges to give out, any exclusions, and scope options for default gateway, etc.
Why do you have to activate a DHCP scope?
A DHCP (Dynamic Host Configuration Protocol) scope defines the valid pool of IP addresses that can be assigned to the network. You need to activate a DHCP scope so that the IP addresses that are issued (or leased) to the client devices will be compatible with the network configuration. If a client is issued an invalid IP address it will not be able to communicate on the network.
19 What is a requirement of a DHCP reservation?
They have to be created within a scope and not be excluded from the scope... MAC address also needed.
What command create DHCP address pool on a router?
router (config)# ip dhcp servicerouter (dhcp-config)# ip dhcp pool router (dhcp-config)# network
What tool is used to configure a DHCP scope?
For a Windows based system you use the DHCP MMC snapin console. This is installed when the DHCP server service is installed. For Linux and Unix based systems you can edit the DHCP configuration file in /etc
What three things must be included in a DHCP scope?
IP, Subnet, and gateway
What is scope and super scope?
A DHCP scope is a valid range of IP addresses which are available for assignments or lease to client computers on a particular subnet. In a DHCP server, you configure a scope to determine the address pool of IPs which the server can provide to DHCP clients. Scopes determine which IP addresses are provided to the clients. Scopes should be defined and activated before DHCP clients use the DHCP server for its dynamic IP configuration. You can configure as many scopes on a DHCP server as is required in your network environment Using superscopes A superscope is an administrative feature of DHCP servers running Windows Server 2003 that you can create and manage through the DHCP console. Using a superscope, you can group multiple scopes as a single administrative entity. With this feature, a DHCP server can:Support DHCP clients on a single physical network segment (such as a single Ethernet LAN segment) where multiple logical IP networks are used. When more than one logical IP network is used on each physical subnet or network, such configurations are often called multinets.Support remote DHCP clients located on the far side of DHCP and BOOTP relay agents (where the network on the far side of the relay agent uses multinets).In multinet configurations, you can use DHCP superscopes to group and activate individual scope ranges of IP addresses used on your network. In this way, the DHCP server computer can activate and provide leases from more than one scope to clients on a single physical network. Superscopes can resolve certain types of DHCP deployment issues for multinets, including situations in which: The available address pool for a currently active scope is nearly depleted, and more computers need to be added to the network. The original scope includes the full addressable range for a single IP network of a specified address class. You need to use another IP network range of addresses to extend the address space for the same physical network segment.Clients must be migrated over time to a new scope (such as to renumber the current IP network from an address range used in an existing active scope to a new scope that contains another IP network range of addresses).You want to use two DHCP servers on the same physical network segment to manage separate logical IP networks.Superscope configurations for multinets The following section shows how a simple DHCP network consisting originally of one physical network segment and one DHCP server, can be extended to use superscopes for support of multinet configurations. Example 1: Non-routed DHCP server (before superscope) In this preliminary instance, a small local area network (LAN) with one DHCP server supports a single physical subnet, Subnet A. The DHCP server in this configuration is limited to leasing addresses to clients on this same physical subnet. The following illustration shows this example network in its original state. At this point, no superscopes have been added and a single scope, Scope 1, is used to service all DHCP clients on Subnet A. Example 2: Superscope for non-routed DHCP server supporting local multinets To include multinets implemented for client computers on Subnet A, the same network segment where the DHCP server is located, you can configure a superscope which includes as members: the original scope (Scope 1) and additional scopes for the logical multinets for which you need to add support (Scope 2, Scope 3). This illustration shows the scope and superscope configuration to support the multinets on the same physical network (Subnet A) as the DHCP server. Example 3: Superscope for routed DHCP server with relay agent supporting remote multinets To include multinets implemented for client computers on Subnet B, the remote network segment located across a router from the DHCP server on Subnet A, you can configure a superscope which includes as members: the additional scopes for the logical multinets for which you need to add remote support (Scope 2, Scope 3). Note that since the multinets are for the remote network (Subnet B), the original scope (Scope 1) does not need to be part of the added superscope. This illustration shows the scope and superscope configuration to support the multinets on the remote physical network (Subnet B) away from the DHCP server.
What do you initially need to configure on a DHCP server in order to give out IP addresses to clients?
a scope
Describe the process of installing a DHCP server in an?
WIndows and non-Windows systems install DHCP in different ways, but the basic idea is the same group of steps:Add the DHCP service role to the systemActivate the serviceAdd the scope of IP addresses and exclusions to the DHCP serviceActivate the scopeOff you go - addresses!
What is the functions of a server?
Dynamic Host Configuration Protocol(DHCP) Server is used to distribute IP in the network automatically from the range specified in the DHCP Server while creating scope. -- By MyNarutoAnime ----
What is the first action that must be done when configuring the DHCP services in Windows Server?
Add a new scope
