0
R3#configure terminal
R3(config)#access-list 104 permit ip 10.0.0.128 0.0.0.127 any
R3(config)#ip nat inside source list 104 interface Serial0/0/0 overload
R3(config)#interface fastEthernet0/1
R3(config-if)#ip access-group 104 in
R3(config-if)#ip nat inside
R3(config-if)#exit
R3(config)#interface Serial0/0/0
R3(config-if)#ip nat outside
R3(config-if)#exit
R3(config)#interface Serial0/0/1
R3(config-if)#ip nat outside
R3(config-if)#end
Writing by vanhuuvt32
bonphuonglanha@gmail.com
Add your answer:
Earn +20 pts
Is there a way to hook up a PC1 to a PC2 and have PC2 acts as a printer?
Yes. You will need ethernet cards for both computers, and a router. After cabling the system together, you will need to enable 'printer sharing' on PC2. Then, you will have to configure 'netowrk printer' on PC1 to be the printer on PC2.
What is the difference between pc1 and pc2?
Pc1 varies from 256 mb to 1 gb while pc2 varies from 512 mb to 2 gb Pc2 chips are more modified and smaller than pc1
What is the valve clearance of Isuzu v10 pc1?
22 mm
What mean by PC1 of a project?
what is PC 1 related to project management
Which device will send a response to the initial tracert packet from PC1?
LON don
Can you still extend windows media center without an extender?
Not exactly. If you have a PC with Windows Vista Media Center (VMC) installed on it--let's call this PC1--you may set PC1's "Recorded TV" directory as a shared folder for the second PC's (PC2's) local Recorded TV directory. In this instance, you could watch and play back recorded HDTV or SDTV from PC2. By setting sharing and permissions on content directories on PC1, you could also set the same media access points on PC2. That said, if PC2 is being used as an 'extender', you should be aware that it cannot stream Live TV from PC1. PC2 cannot access any of PC1 VMC's services or features; it can really only look at the same directories and playback from there.
Devices in the topology diagram require an Ethernet cable between them?
PC1 to Switch, Switch to R1, C2 to R2
Hi.I am stock market trader.Lets say i have 10 PC. PC1 is logged with user "Adam" credentials..PC10 is logged with user "James" credentialsIf i perform an action from PC1, i need the same thing to performed in sync in all the other 9 PC.Is it possible?
A pc Adam james.
What is the answer for 7.6.1 packet Tracer Skill Integration Challenge Activity?
PT Activity 7.6.1: Packet Tracer Skills Integration Challenge Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/0 172.17.50.1 255.255.255.0 N/A Fa0/1.10 172.17.10.1 255.255.255.0 N/A Fa0/1.20 172.17.20.1 255.255.255.0 N/A Fa0/1.88 172.17.88.1 255.255.255.0 N/A R1 Fa0/1.99 172.17.99.1 255.255.255.0 N/A Internet 172.17.88.25 255.255.255.0 172.17.88.1 WRS2 LAN 172.17.40.1 255.255.255.0 N/A Internet 172.17.88.35 255.255.255.0 172.17.88.1 WRS3 LAN 172.17.30.1 255.255.255.0 N/A Addressing Table continued on the next page All contents are Copyright © 1992-2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 5 CCNA Exploration LAN Switching and Wireless: Basic Wireless Concepts and Configuration PT Activity 7.6.1: Skills Integration Challenge All contents are Copyright © 1992-2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 5 Addressing Table continued S1 VLAN 99 172.17.99.31 255.255.255.0 172.17.99.1 S2 VLAN 99 172.17.99.32 255.255.255.0 172.17.99.1 S3 VLAN 99 172.17.99.33 255.255.255.0 172.17.99.1 PC1 NIC 172.17.10.21 255.255.255.0 172.17.10.1 PC2 NIC 172.17.20.22 255.255.255.0 172.17.20.1 Learning Objectives • Configure and verify basic device configurations. • Configure VTP. • Configure trunking. • Configure VLANs. • Assign VLAN to ports. • Configure STP. • Configure router-on-a-stick inter-VLAN routing. • Configure wireless connectivity. • Verify end-to-end connectivity. Introduction In this final Packet Tracer Skills Integration Challenge activity for the Exploration: LAN Switching and Wireless course, you will apply all the skills you have learned including configuring VLANs and VTP, optimizing STP, enabling inter-VLAN routing and integrating wireless connectivity. Task 1: Configure and Verify Basic Device Configurations Step 1. Configure basic commands. Configure each switch with the following basic commands. Packet Tracer only grades the hostnames and default gateways. • Hostnames • Banner • Enable secret password • Line configurations • Service encryption • Switch default gateways Step 2. Configure the management VLAN interface on S1, S2, and S3. Create and enable interface VLAN 99 on each switch. Use the addressing table for address configuration. Step 3. Check results. Your completion percentage should be 13%. If not, click Check Results to see which required components are not yet completed. Task 2: Configure VTP CCNA Exploration LAN Switching and Wireless: Basic Wireless Concepts and Configuration PT Activity 7.6.1: Skills Integration Challenge All contents are Copyright © 1992-2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 5 Step 1. Configure the VTP mode on all three switches. Configure S1 as the server. Configure S2 and S3 as clients. Step 2. Configure the VTP domain name on all three switches. Use CCNA as the VTP domain name. Step 3. Configure the VTP domain password on all three switches. Use cisco as the VTP domain password. Step 4. Check results. Your completion percentage should be 21%. If not, click Check Results to see which required components are not yet completed. Task 3: Configure Trunking Step 1. Configure trunking on S1, S2, and S3. Configure the appropriate interfaces as trunks and assign VLAN 99 as the native VLAN. Step 2. Check results. Your completion percentage should be 44%. If not, click Check Results to see which required components are not yet completed. Task 4: Configure VLANs Step 1. Create the VLANs on S1. Create and name the following VLANs on S1 only. VTP advertises the new VLANs to S2 and S3. • VLAN 10 Faculty/Staff • VLAN 20 Students • VLAN 88 Wireless(Guest) • VLAN 99 Management&Default Step 2. Verify that VLANs have been sent to S2 and S3. Use the appropriate commands to verify that S2 and S3 now have the VLANs you created on S1. It may take a few minutes for Packet Tracer to simulate the VTP advertisements. Step 3. Check results. Your completion percentage should be 54%. If not, click Check Results to see which required components are not yet completed. Task 5: Assign VLANs to Ports Step 1. Assign VLANs to access ports on S2 and S3. Assign the PC access ports to VLANs: • VLAN 10: PC1 • VLAN 20: PC2 CCNA Exploration LAN Switching and Wireless: Basic Wireless Concepts and Configuration PT Activity 7.6.1: Skills Integration Challenge All contents are Copyright © 1992-2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 4 of 5 Assign the wireless router access ports to VLAN 88. Step 2. Verify VLAN implementation. Use the appropriate commands to verify your VLAN implementation. Step 3. Check results. Your completion percentage should be 61%. If not, click Check Results to see which required components are not yet completed. Task 6: Configure STP Step 1. Ensure that S1 is the root bridge for all spanning tree instances. Use 4096 priority. Step 2. Verify that S1 is the root bridge. Step 3. Check results. Your completion percentage should be 66%. If not, click Check Results to see which required components are not yet completed. Task 7: Configure Router-on-a-Stick Inter-VLAN Routing Step 1. Configure subinterfaces. Configure the Fa0/1 subinterfaces on R1 using the information from the addressing table. Step 2. Check results. Your completion percentage should be 79%. If not, click Check Results to see which required components are not yet completed. Task 8: Configure Wireless Connectivity Step 1. Configure IP Addressing for WRS2 and WRS3. Configure LAN settings and then static addressing on the Internet interfaces for both WRS2 and WRS3 using the addresses from the topology. Note: A bug in Packet Tracer may prevent you from assigning the static IP address first. A workaround for this issue is to configure the LAN settings first under Network Setup. Save the settings. Then configure the static IP information under Internet Connection Type and save settings again. Step 2. Configure wireless network settings. • The SSIDs for the routers are WRS2_LAN and WRS3_LAN, respectively. • The WEP for both is 12345ABCDE. Step 3. Configure the wireless routers for remote access. Configure the administration password as cisco123. Step 4. Configure PC3 and PC4 to access the network using DHCP. PC3 connects to the WRS2_LAN, and PC4 connects to the WRS3_LAN. CCNA Exploration LAN Switching and Wireless: Basic Wireless Concepts and Configuration PT Activity 7.6.1: Skills Integration Challenge All contents are Copyright © 1992-2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 5 of 5 Step 5. Verify remote access capability. Step 6. Check results. Your completion percentage should be 100%. If not, click Check Results to see which required components are not yet completed. Task 9: Verify End-to-End Connectivity Step 1. Verify that PC1 and Web/TFTP Server can ping each other. Step 2. Verify that PC1 and PC2 can ping each other. Step 3. Verify that PC3 and PC1 can ping each other. Step 4. Verify that PC2 and PC3 can ping each other.
How do you change the display name of a PC in packet tracer?
Double click the bottom label. For example: PC0 or PC1 and type the name you want to give it.
Which PDU is associated with each source address or port as PC1 communicates with the web server?
1052: segment00-C0-E1-05-A4-68: frame192.168.1.5: packet
Ccna 1 final exam answers?
Refer to the exhibit. What default gateway address will be assigned to PC1 if access to remote resources is needed?
