0
What else can I help you with?
Which computer desk would be the easiest to assemble?
The OfficeMax Corner Computer Desk is easy and light weight too
Do you need a computer to be a engineer?
You do not need a computer to be a engineer. However, a computer will be needed for certain types of engineers or would really help.
What two types of cables would most commonly be used for new runs?
Fiber or Cat6, depending on the funds available and the size of the network.
What is one example of a legal use for proxy server software?
A proxy server may be used legally for many applications. One example would be a content filter on a intranet so that you can stop networked clients from accessing restricted sites on the internet.
How can I enhance my computer for online gaming my OS is vista starter and the size of my ram is 1 gig my proccessor is AMD sempron 3200 1.8Ghz. answer please?
Memory is the easiest upgrade to improve your performance. Two to four gigs will make a great difference. An upgrade processor would also help if they are available in your area.
Can you convert a DC motor to run on AC?
The easiest way would be to convert the AC power to DC by using a rectifier diode and a filter capacitor. In that way you can now run your DC motor on DC.
Why the filter used in rectifier circuit?
Filter capacitors smooth out the pulsating DC. Without the capacitors, the pulsating DC drops to zero at the AC crossing point, unless it is a three phase rectifier. Sometimes, that is sufficient. Sometimes, they are followed up with a regulator circuit that further stabilizes the DC.
What are the gentle and easiest training smaller dog types?
I would say chiwawas
What is the difference between controlled and uncontrolled rectifier?
A simple rectifier is a diode. It only has two terminals and will only allow electron flow in one direction only. A controlled rectifier (SCR=silicon controlled rectifier) has a third connection (gate). Which as the name suggests, is a gate that controls at which point the rectifier will work. It therefore has a level of control.There are various types and you would need the application specification, to get the best use of them.
Which rectifier have highest ripple frequency?
The three phase bridge rectifier has the highest ripple frequency. In a 60 Hz system, the ripple frequency would be 360 Hz. If it were a one phase bridge rectifier, the ripple frequency would be 120 Hz.
How would three phase power be supplied to a DC disc brake?
The AC supply would have to be changed to DC supply.. This would be done with the use of a rectifier. It would be done usually with a full wave rectifier.
Why a full wave rectifier is preferred over a half wave rectifier?
The a.c. component, or ripple, produced by the 4-diode (full wave) bridge rectifier is the same as that produced by the 2-diode full wave rectifier. The bridge is connected across the secondary winding of a transformer. The 2 diodes of the other type of full wave rectifier are each connected to one end of a winding, but that winding requires a center tap. For any desired value of d.c. after rectification, the a.c. voltage of the 2-diode rectifier winding has to be twice that of the winding required for the bridge.
What kind of unemployment would be easiest to tolerate and why?
Frictional unemployment, because it does not last longer than the other types of unemployment.
How is AC converted to DC and does it change the power an item would have?
you basically use rectifiers..like zener diode rectifier and full bridge rectifier..
Solidstate rectifier versus tube rectifier in guitar amplifiers?
A: There is no difference much in performance. But if a tube is replaced by a solid state rectifier the gain would be approximately 100 volts and assuming the DC caps are rated for this higher voltage it would be OK. Since there is higher voltages the dynamic of the amplifier will change accordingly.
How would DC be obtained from a three phase supply?
By using a three-phase rectifier.
What happen when two of four diode in a bridge rectifier is short circuit?
If two diodes in a bridge rectifier circuit are short-circuited, the circuit would behave as if it were a full-wave rectifier instead of a bridge rectifier. This means that the output would not be fully rectified, and there would be additional AC voltage ripple present in the output. It is crucial to replace the short-circuited diodes to restore the correct operation of the rectifier circuit.
