To update BIOS settings on a Compaq Presario V3000, you will first need to download the latest BIOS update from the official Compaq website. Ensure your laptop is connected to a power source throughout the update process to prevent any interruptions. Follow the specific instructions provided with the BIOS update file to successfully update the BIOS settings on your Compaq Presario V3000. Remember to proceed with caution, as updating the BIOS incorrectly can potentially harm your laptop.
You can purchase a Compaq Presario V3000 online at sites like Amazon, and Newegg. You may also be able to purchase this a Compaq Presario V3000 at Best Buy.
$110.49
hello I have a compaq presario v3000, I upgrade a porogram windows xp, afer that the drivers was not installed.
Some of the specs that come with a Compaq V3000 laptop include a 6 cell battery and dual core Intel microprocessor. Another spec of this laptop is that it has a 14" widescreen display.
have you tried attaching a usb keyboard? worked for me. also try looking up service manual to see how to install/uninstall keyboard. ribbon cable may just be lose.
hold f11 during startup, when the recovery screen comes up, choose advanced options then destructive recovery. it will prompt you to back up all files before doing so as this will wipe it fully. sit back and grab a case of cold ones, its gonna take a while.
vbox v3000
i would like to upgrade my V box V3000 reciver, please provide me detail procedure and possible source for get renewed. and i need your help to get the new software with the way for installation procedure thanks alot every body . ahmad almubaikhi
stop formatting you arent helping, the problem is the heatsink grease is worn off your gpu and it is over heating so it is turning off due to temperature protection. high temps also cause lagging in cpus too. just find some heatsink grease not regular grease take the fan off and the cooling fins and clean any old grease left on and reapply a small even amount on the gpu processor and replace parts you should be fine from there.
you have a problem in the power board inside your receiver and it should replaced with a new power board. Actually there is an IC in the power board which become HOT and make the system restart. Usually this happens during watching scrambled channels. I have resolved the problem myself by installing a small fan inside the receiver in order to cool the IC above.
I purchased the Bush Platinum spark plugs and cables. Total cost: about $115.00. The work took about 4-5 hours; I did not want to rush this at all! � Here is what we did: 1. Remove Air intake (this is easy to say... but just take your time, it is not impossible to get the job done). 2. Loosen the V3000 (LS) air cover, just undo the screws the hold that part. 3. Number your old spark plug cables so you know where they go. 4. Replace ONE spark plug at a time and change the old cable for a new cable of the same length (mark the new cable with the same number of your old cable in case you loose track later). 5. Place the V3000 (LS) back in place, do not over-tighten the screws! 6. Place back into place the Air filter tube; make all the connection previously removed and you should be finish. Take your time and do not rush this work - if needed take some pictures with your digital camara to remember where things go. On a difficulty scale of 1 to 5, I give this work a 3 AA Visit this website for full details http://www.monterosportonline.com/diy.html I purchased the Bush Platinum spark plugs and cables. Total cost: about $115.00. The work took about 4-5 hours; I did not want to rush this at all! � Here is what we did: 1. Remove Air intake (this is easy to say... but just take your time, it is not impossible to get the job done). 2. Loosen the V3000 (LS) air cover, just undo the screws the hold that part. 3. Number your old spark plug cables so you know where they go. 4. Replace ONE spark plug at a time and change the old cable for a new cable of the same length (mark the new cable with the same number of your old cable in case you loose track later). 5. Place the V3000 (LS) back in place, do not over-tighten the screws! 6. Place back into place the Air filter tube; make all the connection previously removed and you should be finish. Take your time and do not rush this work - if needed take some pictures with your digital camara to remember where things go. On a difficulty scale of 1 to 5, I give this work a 3 AA This website gives an in depth description of how to do it w/ pictures.... http://www.monterosportonline.com/diy.html The above post really does you no good. Though pictures are there, they do not reflect a 1995, which is a bit more complicated. I'm doing a search myself at the moment. There aren't many answers here. check out this site.. it worked for my 96. perhaps it'll help you http://www.monterosportonline.com/diy.html
The wireless bridge function is no longer available. All recent versions of the Belkin F5D7230-4 router (version 7000 and above) no longer support this function although I cannot find any announcement on the Belkin website. Check the version number on the outside of the package. The web screen for version 7000 does not have the "wireless bridge" option.This is from a search I did on the Belkin web site. This tells you how to setup the router to become a bridge.How To: Configure WDS (Wireless Bridging) with the 54g routerThe information in this article applies to the following products:802.11g Wireless DSL/Cable Gateway Router (F5D7230-4)802.11g Wireless Network Access Point (F5D7130)Router Configuration1. Open a Web Browser 2. In the address bar type http://192.168.2.1 3. Click on Wireless Bridge in the left hand column under Wireless 4. Enter your password if any and click Submit 5. Check the box that says Enable Wireless Bridging, click Apply Changes. 6. Click Home, note the WLAN MAC address under LAN settingsAccess Point Configuration.1. Open a Web Browser 2. In the address bar type http://192.168.2.254 3. Click on Wireless Bridge in the left hand column under Wireless 4. Enter your password if any and click Submit 5. Check the box that says, Enable Wireless Bridging 6. Check the box that says, Enable ONLY specific Access Points to connect and enter the WLAN MAC address from the router, click Apply Changes. Note: The channel must be identical on both the router and the access point.Note: The WDS feature is not completely specified in IEEE or Wifi standards. Therefore interoperability between 802.11 products of different vendors is not guaranteed.Yes, you can, but only using Belkin Router and Access Point, or 2 Belkin Routers (one configured as AP).You must set the MAC Addresss of AP in the Router and the WEP (Also channels must match).I have 2 Belkin routers in Bridge. You know it is working when you get DHCP from the AP. I tried using two belkin routers (802.11g, Firmware 4.05.03, Boot 2.01.09, Model F5D7230-4V4) in a chain. The layout is like this:Cable Modem