0
What else can I help you with?
What three components must be compatible with every other component in the computer?
Motherboard
Does computer speed depend on RAM?
Computer speed depends on many factors, depending on what you need it to do. The required components must work in concert, with the lowest spec one usually limiting the others. In short, low RAM may limit a computer's performance, but it is more likely to be a combination of factors, usually software.
What are the three components of Form Factor?
The component that must be compatible with every other component of the computer is the motherboard. Your computer will not function properly without them being compatible.
What does overclocking your CPU mean?
Overclocking is a process by which internal components on a computer's motherboard are "tweaked" in order to improve the manufactures specifications and overall performance of the machine. Components that are overclocked are the CPU and the system bus. Information supplied by wisegeek.com/what-is-overclocking.htm explains the overclocking process. Overclocking the CPU - In general CPU chips are tested by the manufacturer to see at what speed they fail. They are then rated at a speed one step lower than this. Since the tests are quite stringent the idea is that it may be possible to push the CPU somewhat faster than its rating while maintaining stability in the system. Sometimes, when manufacturers are short on stock, they package faster GHz chips as slower ones; overclockers perceive this as a windfall. Results from overclocking the CPU alone must be balanced against the rest of the system's specifications, namely the bus speed of the motherboard, memory, et cetera. For example, a 20% increase in processor speed does not usually translate to a 20% overall improvement. The CPU might be running faster than the rest of the system, operating in a "hurry up and wait" environment. Therefore the increase might deliver a nice benchmark improvement but little real-world difference. Unsuccessful overclocking can result in an unstable system at best, and in the worst case scenario can damage the CPU. Though the latter is less common, it happens. Pushing also reduces the lifetime of the processor an indeterminable amount, as it forces the chip to work harder and hotter. Cooling fans and a good heatsink become even more important in this case. Overclocking the System Bus - Changing the motherboard bus speed successfully can create a noticeable improvement on the entire system because all components will run faster. Since the processor's effectiveness is helped by the bus speed, an improvement here can also utilize the full benefit of the CPU. However, overclocking the system bus is risky because it means pushing every component on the motherboard. Some people mistakenly believe that if a motherboard offers varying bus speed options they must be supported and therefore safe to use. The problem is that the components you install may not be tested at, or rated for the higher bus speed. Changing this setting affects the CPU (unless you adjust the clock multiplier), the chipset, memory bus, system cache, system memory, built-in IDE hard disk controllers, PCI I/O bus slots, and all peripherals. All components must be able to handle the change for the system to successfully perform without hardware failures. Manufacturer warranties do not cover problems created by overclocking. While pushing a system might start out problem-free, several months down the road when components have aged due to use and temperature changes, instability can crop up. This is more likely to occur when the overclocking was already at the brink of what the system could withstand. When problems do arise - even a program crash - it can no longer be taken for granted that the crash is due to a software glitch. Troubleshooting a system that is overclocked can be an exercise in frustration. The variables increase exponentially and the ability to rule out potentials is made more difficult as hardware might be acting in unpredictable ways.K.DavisAnswerOverclocking is running a processor at a higher frequency than its recommended by the manufacturer which can result in an unstable system but its is a popular thing to do when a computer is used for gaming. cduarte305AnswerOverClocking is a process in which you tweak the CPU and other components on your motherboard (such as northbridge , vdimm etc) What you are doing is over speccing.. or raising the voltage and frequency of your CPU and certain chipset components to obtain a frequency that is above manufacturers spec... resulting in a higher speed and or fronts side bus... dangerous for novice users just remember that COOLING is your biggest worry so if you overclock be sure to have your cooling laid out and that it will regulate at the new temps you will get... it goes alot deeper than this but these are the basics... By |-|3x@|_o7AnswerFor newer motherboards and processor, you can override the default frequencies by changing a setting in CMOS setup. Running a motherboard or processor at a higher speed than the manufacturer suggests is called over clocking and is not recommended because the speed is not guaranteed to be stable. Also, know that running a processor at a higher-than-recommended speed can result in overheating, which can damage the processor.
What are the four steps for correctly soldering components to a printed circuit board?
1. Remove the soldering iron from the holder and wipe the tip on a sponge. 2. Heat the joint to be soldered. 3. Apply solder to the joint. 4. Apply a small bit of solder to the tip of the soldering iron and return it to the holder.
What are two components that must utilize the same front side bus?
CPU and RAM as they both are the main sources of speed in the computer.
Components that must use the same front side bus speed?
motherboard and cpu
What components of fitness must you have for tennis?
you must have agility, speed and power.
What fitness components must you have for tennis?
Speed, Endurance and Strength are important for tennis.
What are 2 components that must use the same side bus speed?
RAM (Random Access Memory)
What fitness components must you have in ice hockey?
There are a number of fitness components necessary for hockey. Some of these include good cardiovascular endurance, speed, as well as good control of the stick and puck.
How reliable is the VOIP service compared to a traditional landline.?
Voip is almost as reliable as traditional landlines however you must have high-speed broadband Internet service to utilize quality sound.
What must match the type and speed of the physical network being used?
All of the components must be at the same speed or higher - this would include all the cables, the network interface cards, and any network connectivity devices such as hubs, switches, routers, etc.
Why must the solvent front be near the top of the filter paper?
Having the solvent front near the top of the filter paper ensures that the separation process is efficient by allowing the components to be carried up the paper evenly. This helps prevent overlap of the separated components and ensures a clear resolution of the different compounds in the mixture.
Which components use the front-side bus?
The Front-Side Bus lies between the CPU and the Northbridge chipset. The Northbridge chipset controls the highspeed devices on the motherboard such as PCI components, Memory, and AGP Video, however the Northbridge needs a direct communication link to the CPU in order to when to send data to control these devices. That's where the FSB comes into play and provides that direct link. One wishing to overclock their system must take into the speed of the Northbridge chipset as it plays an important part in determining Overclocking speeds.
How do you fix Turbine Speed Sensor Malfunction?
If one of the turbine speed sensors is malfunctioning locate the broken part must be found. This is done by using a diagnostic machine. A broken sensor will need to be replaced in order for the components to work correctly.
What components of fitness must you have for yoga?
flexibility
