answersLogoWhite

0


Best Answer

About the most common application of flue gas is as a heat source. Recall that flue gas is the stack gas from plants fired with combustibles (coal, oil, gas, biomass, etc.), and it exhausts into the atmosphere. We spend a lot of money monitoring stack gas to keep the combustion process as tightly controlled as possible. That minimized emissions.

The heat in the stack gas can be used to heat water or the like, and the preheated water can then be fed back into the boilers to create the steam that drives the turbines that generate electric power (which is one example, but a common one). The heating of the (boiler) feedwater with the flue gas increases the efficiency of the whole operation. It's classic steam cycle power generation, and the preheating of feedwater within the stack (by the flue gas) is a time-proven tactic to reduce costs.

User Avatar

Wiki User

βˆ™ 13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is an application of flue gas?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Chemical Engineering

What does a flue gas desulphurisation plant do?

A flue gas Desulphurisation (FGD) plant removes Sulphur Dioxide from the flue gas before it is released into the atmosphere and hence reduces our impact on the environment.


What is the need of Purging in boiler?

purging is a cleaning process which cleans explosive items in air,flue gas path if any.


What is the best way to clean flue pipes?

The best way to clean flue pipes is to check that the connection is clean and remove the flue pipe, use a flue cleaning brush to brush it down in an up and down motion to remove all the build up.


What is a gas furnace heat exchanger?

The heat exchanger is the metal wall or tubing that is heated up when the burners are ignited. The inside of the heat exchanger allows the toxic flue gases produced from the burners to exhaust out through the furnace flue. The outside of the heat exchanger is where the cold air passes over, becomes warmed, and is blown throughout the ductwork of the home. The heat exchanger is the only wall separating the toxic flue gases from the supply air. If a crack develops in the heat exchanger, there is a potential for carbon monoxide gas to leak over to the supply side and be blown throughout your rooms. Carbon monoxide gas is odorless. The human senses will not detect its presence. Ron Ferrara- DHR Mechanical Services, Inc.


Why would a flexible flue liner be recommended for a chimney?

A flue liner is a flexible sleeve inside the pipe that carries the combustible products, such as smoke, up from the fire away from the living area, and into the atmosphere, outside the house. A liner is needed in case the flue is cracked or damaged, causing the smoke to stay in the house, or causing cold wind from the outside to come into the house. A flue liner is added protection to keeping the house safe from fumes.

Related questions

What are three instruments that a flue-gas analysis kit might contain?

A flue-gas analysis kit may contain a gas detector for measuring gas concentrations, a temperature probe for measuring flue gas temperature, and a draft gauge for measuring draft pressure in the flue.


What does a flue gas desulphurisation plant do?

A flue gas Desulphurisation (FGD) plant removes Sulphur Dioxide from the flue gas before it is released into the atmosphere and hence reduces our impact on the environment.


What is a vented fireplace?

Usually refers to a gas fireplace, since wood fireplaces are vented by the flue (chimney) Gas fireplaces can be vented (flue) or unvented (no flue)


Can you run gas furnace and gas hot water heater into one flue?

Of course If the flue is sized properly


Where can someone purchase a flue gas analyzer?

A flue gas analyzer is used to check the chemicals in the gasses in one's flue. They can be purchased at most home improvement stores or stores that have a home improvement section.


How can you calculate flue gas loss on ignecation?

Flue gas loss on ignition can be calculated by measuring the difference in stack gas temperature before and after ignition, along with the flow rate of the gas and its composition. By determining the energy content of the flue gas before and after combustion, the flue gas loss on ignition can be calculated using the energy balance equation. This measurement helps in assessing the efficiency of the combustion process and identifying opportunities for improvement.


What is the charge in flue gas particle?

positive


What is the purpose of a bypass on an industrial boiler economiser?

If the boiler fuel contains Sulphur (and most do) combustion products in the flue gas will include Oxides of Sulphur (SO2 and SO3). SO3 combines with water (H2O) to make Sulphuric Acid (H2SO4). If the temperature of the flue gas falls below the dew point, the combination of the acid with the moisture in the flue gas causes corrosion of the flue gas duct work. Bypassing the economiser in the early stages of a boiler start keeps the flue gas temperature above the dew point.


What is the meaning of flue gas?

Flue gas refers to the gases that are emitted as byproducts from combustion processes, such as in power plants, furnaces, and vehicles. These gases typically include carbon dioxide, water vapor, nitrogen oxides, sulfur dioxide, and particulate matter, and can have environmental impacts if not properly treated before release into the atmosphere.


How do you calculate the flue gas velocity in airpreheater?

To calculate the flue gas velocity in an air preheater, you would need to know the volumetric flow rate of the flue gas passing through the preheater and the cross-sectional area of the preheater. You can then use the formula: Velocity = Volumetric flow rate / Cross-sectional area of preheater. This calculation will give you the velocity at which the flue gas is moving through the air preheater.


What are three instruments that a flue gas analysis kit might contain?

A flue gas analysis kit may contain a digital manometer to measure draft pressures, a flue gas analyzer to measure levels of oxygen, carbon monoxide, and other gases, and a thermocouple for temperature measurement.


Do I open the flue for a gas fireplace?

When burning the firplace, flue must be open to avoid death/ illness from carbon monoxide.