0
Add your answer:
Earn +20 pts
How do you install rear brakes on 2001 Toyota Highlander?
you would install the breaks the same way you do the front ones. 1. open hood , remove cap from brake fluide container . 2. loose wheel ,then jack up ,secure car ,remove nuts on wheel ,take wheel off . 3. loosen the main bolt holding pads together. 4. remove pads 5. place pads on newspaper , remove metal frame from old pads. 6. place new pads on newspaper ,spray brake glue to back of pads 7. put metal frame on new pads. 8. place brake lube on bolt to make brakes work easier 9.install both pads back into harness , use break pusher(clamp) to put pads into place. 10. tighten the break harness bolt (don't over do tightness of the bolt), put wheel back on , put nuts back on then lower car . done repeat each step for each wheel.
How do you remove a rear wheel on a Audi car?
apply handbrake, find the locking wheel nut, remove toolkit from boot, crank the wheel nuts on said wheel (do not remove), affix jack, pump the jack till the said wheel has airtime and remove the loosened wheel nuts. and as ramsey would say 'done'
Where is the rear jacking point for a 1992 GMC Safari van?
the jack position i would assume if no frame would be on the sides where the unibody meets in front of the rear wheel but i am almost certain there is a frame
How do you remove hub bearing on 1996 jeep Cherokee sport 4.0L?
You would need to remove the brake caliper, brake caliper bracket and also the brake rotor. The cotter pin and nut that holds the axle in place also needs to be removed, and then the axle needs to be tapped out of the hub with a socket. Then you can get at the three bolts that hold the hub into place. An instructional video of this procedure has been listed below to help.
Why do you hear a knocking sound when you drive?
Not sure where or when you are hearing the noise but a check of the sub frame that hols the engine is a place to start. The sub frame is bolted to the frame near each front tire. The bolts go through the sub frame, rubber isolators, then into the main frame. Make sure that the rubber isolator and bolt have not pulled through sub frame. Also the other three things would be a broken strut, bad cv joint, or bad wheel bearing.
How do you remove the brake calipers on a Ford Falcon?
Are they drum or disc pads? Tools · Socket set or ring spanners · Flat bladed screw driver · Brake caliper compressor (super cheap stores)$20 This will help you remove disc pads # Remove wheel trim and loosen wheel nuts # Jack tire up until its off the ground and remove wheel nuts and place them into wheel trim and remove wheel. # Inspect the disc pads and rotor which are your wheel discs. # Normally you would have the wheel discs machined so they are even before you replace disc pads. # There are two bolts holding the caliper onto the wheel disc, the disc pads are located inside the caliper. # Sometimes you have remove both bolts to remove the caliper and sometimes can remove one bolt and loosen the other bolt and then use a flat bladed screw driver to lift the caliper and flip it open and then you can remove the old discs # Once you remove the old discs pads check the brake reservoir and remove brake fluid if necessary and use a brake caliper compressor inside the caliper to compress the piston until its flat and even, then you place the new disc pads into the caliper and close the caliper back over the wheel disc, you may have to tap it or wriggle it bit to get it back in place. # Once in place return the bolts and tighten, replace wheel and hand tight, lower tire and tighten, replace wheel trim and take car out and test brakes. # If you don't have a brake caliper compressor tool you may have to remove the 2 bolts and the brake fluid hose to remove caliper to place the caliper on a hard surface and tap the piston until its flat, but then replace the discs pads. # but then you will have to bleed all four brakes. Sam
Do you need to remove the steering wheel in order to remove the dash on a 1996 Ford Ranger?
Well I would say Yes, I have 1997 ranger and I had to pull the dash out twice. Removing the steering wheel made it a lot easer. I disconnected mine from under the dash and took out four nuts holding it to the bottom of the dash frame. Make sure you disconnect the Battery and then the airbag wire under the dash.
Anyone know where you can find a DIY guide for replacing at least the front sway bar on a 97-03 grand prix gtp any advice would be appreciated greatly. also what is the lvl of experience needed.?
Haynes is a good manual for this. This is rather hard as the entire front sub frame (holds engine and tranny) must be lowered slightly in order to slide the sway bar out the driver's side wheel well. 1. Remove left wheel. 2. Raise car and support sub frame with a jack. 3. Disconnect nut at the rack to the steering shaft - under a protective boot (make sure the steering wheel and wheels are straight - try not to disrupt this during entire process). 4. Remove sway bar links and sway bar bushings. 5. Remove rear sub frame bolts, and loosen front bolts a few turns. 6. Lower jack supporting sub frame enough to slide the sway bar out the wheel well. This basically how to remove the sway bar.
How do you replace the clock spring on a 2000 Ford Windstar?
Well, if its anything like the one in my 1994 f150 then you just need to remove the steering wheel and its right there.. You will need to remove the airbag assembly and use a wheel puller to remove the steering wheel. I would also remove the negative bat cable before doing this as you will be messing with the airbag assembly. Dont use a hammer to try and remove the wheel, rent a puller.
How do you remove the engine from a ford power stroke?
The dealer would lift the cab off the frame believe it or not :(
Can a 12 inch unicycle wheel be replaced with a 16 inch?
No, a 12 inch wheel cannot be directly replaced with a 16 inch wheel on a unicycle. The diameter of the wheel determines the size of the frame and other components, so a larger wheel would not fit properly without making necessary adjustments to the unicycle.
How do I remove locking wheel hubs from 1992 Buick Roadmaster?
I would like to know how you put four wheel drive into a luxury car........
