0
Some companies offer a paintless dent removal srvice which is priced by size of dent and location. other than that get behind the dent with a small flat object wood or metal and hammer the block to get rid of the dent. If dent is small use a picking hammer and with the point work around the circle of the dent with the point trying to keep it even with the outside surface. Sand the surface when you get close and go to the flat side of a body hammer and smooth the outside where it got picked out, Apply a small amount fo body filler and sand to even the suface prime sand prime sand with different grits and repaint the surface
Add your answer:
Earn +20 pts
How do you remove the rear bumper cover on a 2004 Nissan Murano?
I have a small dent need to remove it
How do you fix a right front fender dent?
try pop a dent or if you can get it out with that try a rubber mallet if you can get to the back side of it
Crossword. a four letter word describing a fender bender?
dent
Can any average person remove a auto dent with no experience or should you take it to a bodyshop?
If the dent is not cressed an average joe can remove the dent by purchasing an easy out dent remover. They are pretty simple to use and the instructions make it pretty basic for any average joe to figure out. However it the dent has a wrinkle or creace in it, it would be much wiser to seek out professional help, that what they are trained to do. Some tasks are not ment for the average person to do themselves bodyshops are trained and have had schooling to master removing and refinishing a dent. If the dent is small yes if the dent is not and is creased seek out a professional.
How do you remove a fender from a 95 dodge ram1500?
There are seven steps on how to remove a fender from a 95 Dodge Ram 1500. Some of the step-by-step instructions are remove the screws that hold the wheel well to the fender, remove the bolts from the wheel well fender, and then remove the bolts that attach the fender to the rocker panel flange.
How do you replace the fender on a full size ford bronco?
first would be to remove the headlight and turn signal. remove any bolts behind there holding the fender. remove the screws holding the inner fender to the fender. at the bottom of the fender behind the tire there are 1-2 bolts that need to be removed. now open the door and remove the fender bolt/s in the door jamb. last is to remove the 4-5 bolts along the top of the fender under the hood holding the fender to the appron.
How much would it cost to fix a small dent in the wall?
It will cost between $50 and $100 to fix a small dent in the wall, if you hire a carpenter. An individual can fix the small dent in the wall for less than $20.
How do you remove the piece the filter screws into from the fender of a 93 s10 Blazer Removed all bolts Need to remove fender Can't do it with piece attached Is it welded to fender?
I looked at my remote filter on my 93 S10 Blazer and it is bolted to the inner fender which shouldn't need to be removed to remove the fender.
How do you remove the fender on a 1994 f150?
Unbolt and remove everything bolted to the inner fender. Starting behind the headlight assembly, remove most of the bolts all of the way around the fender. With one or two helpers, hold the fender on while removing the remaining bolts, then the fender can be lifted off.
How do you remove front fender 87 cutlass supreme?
how do i remove the front fender to 1996 Oldsmobile cutlas supreme.
Where is transmission control module 2002 Chrysler voyager ec 2.4 engine?
Inside the left front fender, remove the inner plastic fender liner to access.Inside the left front fender, remove the inner plastic fender liner to access.
What is the best way to remove a dent from a car?
There are a number of easy do-it-yourself ways to repair a dent that have worked for people. The best method largely depends on the type of dent. One way is to use dry ice or a hair drier on the dent. This can remove small dents. Another way is to use a toilet plunger to pull out a dent. A third way is to take a hammer to the inside of a dent and gently tap it out. When using any of these methods, one must inspect for paint damage and repair that as well with some matching touch up auto paint. Otherwise, the paint damaged spots can begin to rust.
