answersLogoWhite

0


Best Answer

The timing should be set at 10:4.

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: 91 s10 2.8l 5spd what should base timing be set at?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the correct timing for a 1986 Chevy Camaro 28L?

The order is 1,2,3,4,5,6


Where is the oxygen sensor located on a '89 Beretta w 28L V6?

it should be located on the rear manifold


How many psi is the fuel pump on a 1988 buick century custom v6 28l fi?

Should be around 40 psi


What does the ditloid 28L in the WA mean?

28 Letters in the Word "Antidisestablishmentarianism"


Where is the map sensor located on a 85 camaro 28l?

should be a small black plastic box close to the distributor mounted on a bracket. it will have a couple of wires and a vacuum line the runs to the intake manifold


The hypotenuse of a right triangle is 26 feet long One leg is 14 feet longer than the other Find the length of the shorter leg?

Let the length of the shorter leg be L, then the longer leg is L + 14.By Pythagoras then 262 = L2 + (L + 14)2 = L2 + L2 + 28L + 196 = 2L2 + 28L + 196676 = 2L2 + 28L + 196 : 2L2 + 28L - 480 = 0 : L2 + 14L - 240 = 0This can be factored : L2 + 14L - 240 = (L + 24)(L - 10) = 0As only a positive number answer applies and this is when L - 10 = 0 : L = 10.The length of the shorter leg is 10 feet.


Where is the starter on a 1987 Chevrolet Blazer S10 with a 28L V-6 motor at?

under exaust manifold on passenger side


What is the fuel on 1983 S-10 28L?

gasoline-usually 89 octane. fuel filter is in the rochester 2se carburetor on a 2.8l 1983 Chevy motor.


28l beretta what sensor is located under throttle body but on engine by to small coolant lines spewing oil from it you pretty sure not oil pressure sensor?

could be tps or throttle positioning sensor


What does it mean when you have low levels of Immunoglobulin G Qn Serum?

what does it mean when my IGM is low at 28L


How do you change distributor in 1986 blazer 28l Thanks Sherry?

well here we go,if you have any mechanical knowledge about engines you have to find top dead center of the #1 cylender.on your balancer there will be a timing mark (groove) line it up with the # BAR ON THE TIMING CHAIN COVER.0 degrees. this will be at #1 OR #6. if you have a chiltens manual it will show you a pic of a distributor cap and the rotor botton location for #1. should point to the front more so to the left.mark the button and the housing for later on then mark the distributor shaft to the eng. block position. this makes it eisier for instalation later. unbolt the clamp bolt and remove. asuming you took off the cap and marked all the wires positions, pull the distributor up and out of the engine block. installing a new one is just the oposite. mark the best you can from the old one. you might have to try a few times to line up the rotor position. use a realy long needle nose pliers to turn the oil pump shaft if you need to for gear spline alighnment.once its in replace the holdown clamp and bolt,cap,wires,keep slight snug on clamp then tighten after you completed your timing position with your timing light. get a manual. it has pics and instructions to help you through. good luck.


88 cavalier wagon 28L v6 marked spark plug wires but rubbed off book doesnt tell you which wire runs to what spark plug anyone know?

Here you go. Copy & paste into your browser. http://autorepair.about.com/library/firing_orders/bl-fo-10962.htm