0
Add your answer:
Earn +20 pts
What is the BTU rating for a Heil gas furnace?
It depends on the furnace, they come in different sizes. There should be a data plate on or in the furnace which lists the input and output rating.
How do you find the efficiency of your furnace?
Divide the btu output rating by the btu input rating. Both of these values can be found on the furnace`s nametag.
What is the BTU rating for an American Standard gas furnace?
Read the tag on your furnace for the input/output rating. American Standard and all other manufacturers make more than one size furnace.
How much liters of gas does a home furnace use an hour?
Gas usage is measured in cubic feet because it is a vapor. Look at the tag on your furnace and find the input rating, natural gas contains roughly 1000 btu per cubic foot. So divide the input rating by 1000 and you have your answer.
What size breaker do you use for a furnace?
It depends on the rating of the furnace. There should be a plate or sticker somewhere on the furnace that shows the rating. If you are just powering a blower motor the rating will be lower than if you have an electric heating element.
How much does your propane forced air furnace cost per hour to run?
That would depend on it`s size or input rating. You can get the input rating off the unit nameplate and divide that # by 2500 and that will tell you how many cubic feet of propane vapor the furnace burns per hour. If you buy propane by the gallon ask your supplier how many cubic feet of vapor a gallon of liquid propane yields and you can figure your answer.
How can a furnace be 500 percent efficient?
furnace highest rating is 97 % efficient for a residential model. This is known as a condensing furnace.
Can you put smaller jetting in your natural gas furnace?
No... that would be underfiring it, causing the inside of the furnace to become a dangerous, sooty mess. If you are looking to save fuel I would say the proper way to go is to have a Manual J heat load calculation done on your home and then if indicated switch to a smaller or more efficient furnace. Furnace size is indicated on the mfr`s unit tag as BTU Input (fuel required to produce stated output). The BTU Output rating is the rated Output after allowing for inefficiency losses (what is lost up the chimney). For example a furnace with an input rating of 100,000 BTU and an output rating of 80,000 BTU is an 80% efficient furnace. Supposing your Heat Load calculation says an 80,000 output is what you need, you can save by switching to a 90% efficient 90,000 Input furnace which will have an Output of 81000 BTU/hour (90,000 x 90%) same Output/less Input (fuel). Input is the fuel usage rating, ie Natural Gas provides 1000 BTU/hour per cubic foot used. Therefore with the 100,000 BTU/hour Input furnace, you will use 100 cubic feet of gas for every hour it is running, You can see this on your gas meter, First note the BTU input of your furnace from the tag, divide that # by 1000 (1000 BTU/hour per cubic ft) then divide the result by 60 (60 minutes in an hour) = X cubic feet. Then with the furnace being the only gas appliance in the house operating watch your meter for 60 seconds and if everything is operating properly the reading you get will equal X.Then do the math in reverse X times 60 times 1000 and you should have the Input # you started with. Now going back to the 100,000 80% furnace vs the 90% efficient furnace, it is easy to see one would save 10 cubic feet of gas per hour of run time by upgrading to the 90% or better. In my neck of the woods that equates to a savings of $1.28 for every 10 hours of run time.
What size of unit is a rheem model no rrgg10e36jkr?
100,000 btu input. The output depends on the efficienct rating of the furnace, ie 95%efficient = 95,000 btu output, 80% = 80,000 btu output.
How do you calculate the efficincy of gas burner?
Divide the output rating by the input rating
Is blast furnace a batch furnace?
A blast furnace runs continuously, and input materials are continually dumped in at the top to make their way down through the furnace. Shutting down a blast furnace for relining or other work is a major event in its life.
How many btu does 66000 BTU per HR equal?
The output rating of a 96% efficient boiler or furnace rated at 100,000 input.
