0
Firstly remove the positive battery cable.
Remove the starter motor no need to remove the wiring and leave the starter to rest on the pipework. There is no need to remove it from the engine bay. Your probably asking yourself why the hell did he do that! Just bear with me.
Remove the Power Steering and alternator belts.
Remove the fan and pulley.
Remove the fan shroud if you like I didn't as there is enough room.
With the hand brake on and the gearbox in nuetral jack the vehicle up and place it on stands.
Remove the large front bash plate.
Remove the smaller front guard above this. Note I will not be replacing this as the bash plate provides adequate protection to this area.
Using a 24 mm or 15/16" socket rotate the engine while looking at the exposed flywheel from where the starter motor was removed. As you turn you will see some balancing holes in the face of the flywheel. Some of these holes are deep enough to place a bolt in. It is this that will lock the crankshaft against the bell housing which will enable you to undo the harmonic balancer bolt. Use a bolt that is just a tiny bit smaller than the hole diameter.
Slowly apply force to the bolt until the crankcase locks up then keep going, you will require quite a bit of effort and the bolt will give way with a crack. I used a 3/4 drive socket to remove the bolt although I reckon a 1/2" drive breaker bar will do it.
To remove the harmonic balancer place a screw driver between the balancer and the timing gear cover and gently apply force while hitting the side of the pulley with a soft hammer. I used a brass hammer to provide the shock without damaging the pulley grooves. Be patient and within 5 minutes the harmonic blancer was removed. Note do not lever from the bottom area of the timing cover as it is quite thin use the sides.
Add your answer:
Earn +20 pts
How do you repair harmonic balancer on 94 Geo?
do not repair, replace it only ! For explicit instruction as to procedure, please refer to answer for 1999 ISUZU RODEO crankshaft in automotive section herein.
Holden rodeo timing belt?
when should i replace my timing belt on my rodeo v6 2004 model
When was Holden Rodeo created?
Holden Rodeo was created in 1980.
Is Harmonic Balancer Bolt on 1995 Isuzu Rodeo Left Hand Threaded?
No but they are torqued on at 125 to 130 ft. lbs and as a result, very hard to get broke loose.
Witch direction dose the bolt turn to take off the harmonic balancer on a 1995 rodeo?
Its the normal righty tighty lefty losey. Thats why its torked on with 124 ft lbs. Im having trouble getting it off to replace the hydrolic belt tensinor
What is compression on the cylinders of 2001 Holden rodeo diesel 2.8lt?
The compression on the cylinders of a 2001 Holden Rodeo diesel 2.8lt is not stated. It is stated that the 2001 Holden Rodeo diesel 2.8lt has a high compression g200z motor.
Where is the oil pressure sending unit on a 2000 Isuzu Rodeo 3.2L V6?
It is on the oil cooler manifold, next to the oil pressure switch.look front of engine below harmonic balancer,before oil filter.
Where can one find a used Holden Rodeo 4x4?
One can find a used Holden Rodeo 4x4 at a local used car retailer. Alternatively, one can try looking for a used Holden Rodeo 4x4 for sale online on Craiglist.
How do you remove a Holden radio?
What model mate? A 2007 LX 4X4 Holden Rodeo
How do you tighten front bearing on 05 Rodeo?
Need to know which bearing and which Rodeo. There is a Isuzu Rodeo and a Holden Rodeo. Each has several bearings.
Will holden rodeo wheel fit a VW amarok?
No.
Replace water pump on a 1994 Isuzu Rodeo?
replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo replace water pump on a 1994 rodeo 6 cylinder
