Wiki User
∙ 13y ago200 RMS 4 channel or 2 channel so u know add the rms of the speakers to find the amp rms needed
Wiki User
∙ 13y agoatleast 1 and a half lemons because a 60 watt lightbulb takes thirty lemons so the amount of lemons you use is supposedly half of the watts so if 3 watts would be 1 and a half lemons
It depends what the power rating of the appliance is. A 500 watt microwave will use half a kilowatt if it's run for an hour on full power. A 750 watt unit will use 3/4 of a unit in the same time period.
volts x amperes = watts so amperes = watts / volts X amperes = 700 watts / 12 volts = 58.33 amps Your amplifier draws 58.33 amps. This is assuming that your 700 watt number is actually based on power transferred to the speakers and is actually a number more applicable to lights or motors. Power moving through an amplifier changes up/down incredibly rapidly with the volume and frequency of the sound. That means that you may get 700 watts (and 58 amps), but only for a tiny fraction of a second. In addition an honest 700 Watt amplifier may only put 700 Watts through particular low resistance speakers (a 1 ohm or 2 ohm subwoofer for example where common speakers might be be 4 ohms and only receive half the power). Add that many low end manufacturers are notoriously 'optimistic' about their power levels and you have quite a mess.
That depends upon the mixer and the speed. For example, a 600 watt mixer run at full speed for one hour will consume 0.6 kW-hours in one hour. It would consume 0.1 kW-hours in 10 minutes. A 300 watt mixer run at full speed would use half that much, or 0.05 kW-hours in 10 minutes. Running the 300 watt mixer at half power would cut the power consumption in half again, to 0.025 kW-hours per 10 minutes.
Usually it's rating means "all speakers together at max output". What they don't usually tell you is there's not enough power to run at max output continuously without becoming unstable or getting bad distortion. Amps usually run fine and stable at half their rated max power.
it problably has to do with the amplifier, which is what provides the power to them. this means that it is not able to go this loud so it will shut the connection if nessecary.
That is called "power". The SI unit of energy is the joule, the SI unit for power is the watt, which is equal to joules/second.That is called "power". The SI unit of energy is the joule, the SI unit for power is the watt, which is equal to joules/second.That is called "power". The SI unit of energy is the joule, the SI unit for power is the watt, which is equal to joules/second.That is called "power". The SI unit of energy is the joule, the SI unit for power is the watt, which is equal to joules/second.
A 40-watt bulb refers to the power consumption or energy usage of the bulb. It indicates the amount of electricity the bulb consumes when it is turned on. In general, the higher the wattage, the brighter the light emitted by the bulb.
-3db equates to half of the original power. if you had 1 watt input. and the output is 1/2 watt. The power gain is calculated by 10 log (Pin/Pout) ( in bels its log(Pin/Pout) in decibels its 10 log (Pin/Pout) ) That is 10 log (1/ 1/2) = 10 log 2 = -3 that's -3db for you It communications and in so many other fields. the 3db mark is taken as kind of datum for useful power. that is to say beyond this the magnitude will reduce below half.
if i am not mistaken the front door speakers are 6 in a half inch and the back speakers are 6x8 inch speakers.
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
A 1000 watt output amplifier is a good sized amp. The critical thing here is that the speakers, regardless of size or make must have the same impedance measured in ohms as the amps output. On the back of your amp at the speaker output jacks you should find a printed number with the output impedance 8 ohms is a typical output. But it won't say "8 ohms". It will say 8 followed by the Greek symbol for omega, that symbol that looks like an upside down letter U. This is the symbol for ohms. If you have the manual for the amp, it will be listed in the specification chart. If you are unsure check with the manufacturer to get the correct impedance Then purchase speakers that have the same impedance