0
Add your answer:
Earn +20 pts
How far can you drive the car once the alternator belt breaks?
Till your battery runs dead.
Can you drive without serpentine belt?
You can drive for awhile without the alternator or power steering working but without the water pump working you won't get far without doing serious damage to the engine. So if that serp belt drives the water pump the answer is no.
Where the alternator is located in vectra 2ltr 1999 and how to remove alternator and belt?
under the inlet manfold to the extreme far right
Change belt Toyota Echo 2001?
Replacing (or tightening) the main drive belt is very easy, you will need a 12mm socket wrench and a 14mm open end wrench. Loosen (do not remove) the two bolts above the alternator that are attached to the metal bracket that allow the alternator to slide (the alternator is attached to the topmost pulley that the drive belt touches, it is at the top front passenger side of the engine compartment). There is a 3rd bolt below the alternator, slightly difficult to see, loosen it using the 14mm wrench, it is often difficult to turn, I recommend penetrating oil and a breaker bar, you only need to turn it a little bit to allow the alternator to pivot. Once all three bolts are loose, you can easily rock the alternator back and forth (same procedure is used to tighten the drive belt). You want to push the alternator back to remove the belt. After installing a new belt (or to tighten an existing belt) you need to pull the alternator toward the front of the car as far as possible. The best way to do this is by putting a pry bar on top of and slightly behind the alternator and pushing up toward the windshield while using the engine as a pivot - this gives you plenty of leverage and allows you to pull the alternator forward. While you are prying, you can tighten the bolt that holds the alternator to the bracket using your left hand as you brace the pry bar with your right hand, to hold it all in place.
How do you remove the serpentine belt and power steering belt on a Toyota Echo 2000?
Replacing (or tightening) the main drive belt is very easy, you will need a 12mm socket wrench and a 14mm open end wrench. Loosen (do not remove) the two bolts above the alternator that are attached to the metal bracket that allow the alternator to slide (the alternator is attached to the topmost pulley that the drive belt touches, it is at the top front passenger side of the engine compartment). There is a 3rd bolt below the alternator, slightly difficult to see, loosen it using the 14mm wrench, it is often difficult to turn, I recommend penetrating oil and a breaker bar, you only need to turn it a little bit to allow the alternator to pivot. Once all three bolts are loose, you can easily rock the alternator back and forth (same procedure is used to tighten the drive belt). You want to push the alternator back to remove the belt. After installing a new belt (or to tighten an existing belt) you need to pull the alternator toward the front of the car as far as possible. The best way to do this is by putting a pry bar on top of and slightly behind the alternator and pushing up toward the windshield while using the engine as a pivot - this gives you plenty of leverage and allows you to pull the alternator forward. While you are prying, you can tighten the bolt that holds the alternator to the bracket using your left hand as you brace the pry bar with your right hand, to hold it all in place.The power steering belt is much more difficult but there is an adjustment bolt there as well (I recommend you don't replace that belt unless you have to).
How far could you safely drive 1999 Pontiac GTP with Supercharger without accessory drive belt?
I think you mean the Supercharger belt? You cannot drive anywhere without your accessory belt... You can drive as long as you want without your Supercharger belt but be prepared for a substantial loss in power.
How far can you drive with broken alternator belt?
It depends on the engine...if its carbuerated it will last usually long enough to get you 3 or more miles using the power from the battery, fuel injected much less.because newer cars power fuel pump, injectors . also depends if alternator and water pump are using same belt. but usually car would overheat before it ran out of juice. not far. as soon as the battery goes dead, so will your car
How do you change the drive belt on a 2003 Toyota Echo?
Replacing (or tightening) this belt is very easy, you will need a 12mm socket wrench and a 14mm open end wrench. Loosen (do not remove) the two bolts above the alternator that are attached to the metal bracket that allow the alternator to slide (the alternator is attached to the topmost pulley that the drive belt touches, it is at the top front passenger side of the engine compartment). There is a 3rd bolt below the alternator, slightly difficult to see, loosen it using the 14mm wrench, it is often difficult to turn, I recommend penetrating oil and a breaker bar, you only need to turn it a little bit to allow the alternator to pivot. Once all three bolts are loose, you can easily rock the alternator back and forth (same procedure is used to replace the drive belt). To reinstall or tighten the belt you need to pull the alternator toward the front of the car as far as possible. The best way to do this is by putting a pry bar on top of and slightly behind the alternator and pushing up toward the windshield while using the engine as a pivot - this gives you plenty of leverage and allows you to pull the alternator forward. While you are prying, you can tighten the bolt that holds the alternator to the bracket using your left hand as you brace the pry bar with your right hand, to hold it all in place.
How do you install an alternator for a 1999 Toyota Camry?
Alternators are one of the easiest things to replace on any engine. There are a few easy steps. # Locate the alternator. Disconnect any wires that go to the alternator. # Get that belt off of there. Simply get a socket on the belt tensioner, and pull it as far as you can in whichever way it turns. This will take all that tension off the belt, loosening it so you can remove it. ( You might consider buying a new belt, while you're at it. They're normally pretty cheap.) # Remove any bolts that you can see that hold the alternator in place. If you need a reference, look at the new alternator and locate the bolt holes in both that and the old alternator. # Pull the alternator off. # Put the new alternator on, and fasten the bolts. # Now to put the belt back on. You may need more than one person for this. If it has a serpentine belt (one belt for all accessories), locate on the underside of the hood/somewhere in the engine bay the belt routing diagram.Study it carefully. Know where the belt goes, and which way it goes. Now: put that socket and wrench back onto the tensioner. Have a helper hold the tensioner as far as they can get it to give you as much slack as you can get for that belt. Route the belt around the crankshaft first, then onto the other accessories above it. The alternator is the last accessory you put the belt on to. It normally can be easily slipped on, but if you can't get enough slack, you'll just have to wiggle it around. A lot. 7. Re-connect any wires that were connected to the alternator. There you have a brand new, hopefully working, alternator!
How do you remove alternator?
Most alternators have the following connections: - drive belt from the engine - pivot bolt on the bottom - tensioning bolt(s) on the top - electrical connections Disconnect the battery Remove the drive belt from the pulley on the front of the alternator Loosen the top bolts but do not remove Disconnect the electrical connections to the alternator Disconnect the pivot bolt and slide it out Remove the top bolts and work the alternator loose from the bushings on the bottom Remove alternator from the car The replacement alternator will usually not have a pulley on it, so remove it from the old and install it on the new (impact wrench) The new alternator may not be clocked the same as the old. Take it back to the store and have them clock it to match the old one The only difficulty going back in is the bushings on the bottom may not be far enough apart to permit insertion of the new alternator bottom bracket. I used a C-clamp and a short section of pipe (about 1") to retract the bushing far enough to get it to go in. A socket wrench socket could also be used to press out the bushing just far enough to get the bracket to slide in. This all takes about 1-2 hours if you have the right tools and longer if not.
How do you replace the alternator on a 1999 Chevy Blazer S-10 4wd?
the alternator will be located close to the top of the motor, you will need to loosen the tensioner pulley and remove the serpentine belt, disconnect the elictrical connections at the alternator and remove the alternator mounting bolts. then just lift the alternator out... as far as tools you will need a basic set of sockets and a screwdriver.
How do you replace the alternator on a 1996 Chevy Lumina?
1. Disconnect the battery 2. Place a socket wrench in the belt tensioner and turn it up. This lets you slide the belt off of the alternator. 3. The alternator is held on to the engine with four bolts which need to be removed. 4. On the top of the alternator you will see a wire plug. Remove the plug and loose the bolt that is holding it in place. Then simply remove the alternator. This is pretty easy. I am far from a mechanic but it only took me five minutes to do this.
