0
This information is right in the owner's manual. No comment on the wiper arm if it was pulled up to a stationary position prior to removal of the blade. Force does not seem to snap the arm back to the windshield.
To swing back the arm to the windshield, open the hood to have easy access to the wiper base which has a plastic cover. This cover can be snapped loose with bare hands and this will allow the wiper arm to get unstuck and to go down.
^To whoever wrote that: don't you think that if we HAD the owner's manual or if the owner's manual was helpful that we would get online to get this question answered?
Add your answer:
Earn +20 pts
How do you replace the wiper blade on a 1997 Mercedes C230?
Look at the wiper arm where it attaches to the wiper blade. Then look at the videos below in sources and related links below. The replacement wiper blades should also have instructions on them.
What size to replace wiper blades in 2002 Honda crv?
honda crv 1997 rear wiper blade should be 11", 13" is too big
How do you replace rear wiper motor 1997 Ford Explorer?
how do you replace rear wiper motor on a 1997 ford explorer
How replace rear wiper blade Honda odissey 1997?
The 1997 Honda Odyssey has the most common hook-end wiper arms on both front and rear. See the Sources and Related Links section below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
How do you replace wiper on 1997 rav 4?
They are all pretty much the same. There is a small tab where the end of the wiper arm attaches to the wiper blade assy. When you buy your new blade at any auto parts store the reps behind the counter will glady show you how it is done. Takes less than a minute.
How do you replace wiper motor on a 1997 mercury grand marquis?
how do you get to and replace the wiper moter on a 97 marquis
How do you replace original wiper blades from a 1997 Mercury Cougar?
The method is the same for all 89-97 Cougars (and Thunderbirds). Lift the wiper arm/blade up, then insert a flathead screwdriver into the center to release the spring. Then just pull the blade off from the wiper arm. Most of the time you don't even need a screwdriver. You can basically just pull the blade from the arm. -Coleby
How do you remove wiper blades on a 1997 Subaru legacy?
The 1997 Subaru Legacy has the most common hook-end wiper arms. There will be a little tab or button where the wiper blade is inserted into the hook on the wiper arm. Press and pull wiper blade out of hook. Sometimes you need to rotate and flex the blade a little bit to make enough clearance. See hook arm videos below.
What is wiper blade size of 1997 Ford Taurus?
there it is http://mywiperblades.com/1997-ford-taurus-wipers.htm
How do you fix sticking wiper blade for Mercedes Benz 1997?
IS TIME FOR A REPLACEMENT OR MAKE SURE WHEN OPERATING HAVE THE WINDOW WET SO THEY WORK WITH OUT MAKING A NOISY My wiper blade seemed to be sticking and I replaced the blade.Nothing worked,until I sprayed some moisture repellant underneath the housing at the base of the wiper(underneath the black cover)I also smeared vaseline there with my finger.Haven't had a problem since
Can replace 1997 e320 Mercedes transmission with2001?
can replace 1997e320 mercedes transmission with 2001
How can you change windshield wipers on a 1997 Acura Integra?
The 1997 Acura Integra has hook-end wiper arms. See the Sources and Related Links section below for wiper blade installation videos and correct attachment/length wiper blade sizes. Also, if you purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through. Very simple.
