0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Can you use a 250v 3a fuse to replace a 250v 3.15 fuse?
No
Can you use a 250V 3.15A fuse to replace a 125V 3.15A?
yes. the 250v just means that's the maximum voltage rating the fuse can handle .. so it can def handle 125v. just not vice versa.
Can you use a 125V 15A fuse to replace a 250V 10A fuse?
No, it is not safe to replace a 250V 10A fuse with a 125V 15A fuse. The voltage rating of the fuse must be equal to or greater than the system voltage, and the amperage rating must be equal to or lower than the rated current of the circuit. Using a lower voltage or higher amperage fuse can lead to safety hazards, including potential fire risks.
Can you use a 250v 3a fuse to replace a 125v 3a fuse for equipment voltage is 100volt?
Yes, fuses of a higher voltage can be used safely. What is not recommended is to use a lower voltage fuse on higher voltages.
Can you use 250V 3.15A fuse to replace a 250V 3A fuse?
No, it is not recommended to use a 3.15A fuse to replace a 3A fuse. The 3.15A fuse has a higher current rating and may not provide adequate protection for the circuit. It is best to replace a fuse with the same current rating to ensure proper circuit protection.
Can you use a 250v 15 amp fuse for a 125v 15 amp?
No, it is not safe to use a 250V 15A fuse in a 125V circuit. The voltage rating of the fuse should match or exceed the circuit voltage to ensure safety. Using a lower voltage rated fuse can lead to overheating and potentially create a fire hazard. Always use the correct fuse rating for your circuit.
Can you use a 250V 15A to replace 500V 16A?
No, it is not recommended to use a 250V 15A in place of a 500V 16A. The voltage rating is significantly lower on the 250V part, and the amperage rating is also lower. Using a part with lower ratings can lead to electrical hazards and potential damage to the equipment.
What do the letters in T 6.3 A L 250V stand for?
The letters in T6.3AL250V typically refer to the electrical characteristics of a fuse. T indicates it is a time-delay (slow-blow) fuse. 6.3A specifies the current rating, meaning the fuse will blow if the current exceeds 6.3 amps. 250V indicates the maximum voltage the fuse is designed to protect against.
Can you use a 6A 250v fast blow fuse instead of a 6.3A 250v fast blow in a 250 volt amplifier?
You can it will be safe and no damage will result. However it will blow sooner than the intended fuse would, so the amplifier will no longer have its full normal operating range.
Can you use a MDL for MDA fuse?
Depends on the voltage across the fuse. For fuses rated below 9 amps, the two types are almost identical (MDL has slightly lower AC Interrupting amperages), and both are rated for use up to 250V. For fuses rated above 9 amps, the MDL fuses are rated for use up to 32V, while the MDA fuses are rated for use up to 250V. More info on Cooper Bussmann (link below).
What size standard fuse should be used for a current of 315 amps?
A standard fuse size for a current of 315 amps would not be practical due to the high current flow. It is recommended to use alternative protection devices such as a circuit breaker or contactor for currents of this magnitude.
Can you replace a 400mA 125V fuse with a T10L 250V fuse?
I have a T10L 250V fuse in a control system and don not know what amperage this is. Can someone help ?? You can replace a 400ma fuse with a smaller amp fuse but never with a larger amp fuse. The amperage of the fuse is written on the fuse somewhere. If it has a 125 volt fuse then replace it with a 125 volt fuse. I got that, thanks!! The problem is that there is no amperage indicated on the fuse, only the T10L, and I was wondering if this is just the type of fuse, or if it was a codification of the amperage, like a 10A delayed or something... Class T fuses are non-renewable, current-limiting, and conform to UL 198H. Current ratings range from 0A to 1200A for 300V rated fuses, and 0A to 1,200A for 600VAC rated fuses (DC ratings are also available). The interrupting rating is 200kA rms symmetrical and these fuses are designed for protection of feeders and branch circuits in accordance with the NEC. Class T fuses must be labeled "Current Limiting", and may be labeled "Time Delay" if they pass time-delay requirements. I can find no listing for a T10L fuse in this class, so I cannot find the amp rating on this fuse. My guess is that it is a 10 amp fuse, which is far greater than a 400 ma fuse. So my answer is no, you cannot use this fuse.
