The top (or leading) pin bolt uses the plastic bushing, the bottom bolt should be solid. Here is a snipet from a manual.
NOTE: The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design.
NOTE: It is important to note which caliper pin is designed for the correct bore. The leading caliper pin, or top pin, has a bushing as part of the assembly. The trailing caliper pin, or bottom pin, is a solid design. Ensure that the bolt boots fit securely in the groove of the pin bolts. Be sure not to pinch or tear the boots. If the boots are damaged, they must be replaced.
Should be 2 mounting bolts one on top one on bottom remove these and slide caliper off rotor
The caliper bolts are the long bolts that go horizontally from one side of the mounting bracket, through the top and bottom of the caliper, to the other side of the mounting bracket(if the caliper is supported inside and outside of the rotor, which all the ones I've seen are). The caliper slides on the caliper bolts to adjust to the rotorand usually has expanding dust boots around the boltson both sides of the caliper tokeep the sliding area clean.
The caliper mounting bracket, in 99% of vehicles, needs to be unbolted from the axle before it will release the rotor. There are usually only two bolts holding it. Sometimes you can remove the top bolt, loosen the bottom and swing the mounting bracket out of the way. Sometimes you have to take both bolts completely out and dismount the bracket.
That's the brake fluid bleeder and it should be on top of the caliper. If it is on the bottom you have the left and right caliper mixed up.
On the bottom of the car
LOOSEN& REMOVE THE 2 BOLT FROM BEHIND THE CALIPER TOP & BOTTOM. I THINK ITS A 1/4 IN. SOCKET. THEM YOU MIGHT HAVE TO TAP THE CALIPER WITH A HAMMER TO GET IT LOOSE, WHEN LOOSE REMOVE IT FROM ROATAR..
FRONT BRAKE PAD REPLACEMENT Jack up vehicle and remove the wheel. before removing the caliper , be sure to depress the piston into the bottom of its bore in the caliper with a large C- clamp to make room for the new pads. look behind the caliper and you should see two bolts holding the caliper on. remove the bolts, "DO NOT REMOVE THE BRAKE LINE", the caliper should pull free from the caliper mounting braket. DO NOT LET THE CALIPER HANG BY THE BRAKE HOSE". Separate the brake pads from the caliper mounting bracket." Remove the steel slippers from the upper and lower parts of the caliper mounting bracket. After doing the above You should be done with removal to install follow the above steps in reverse. The rear brakes are the same as the front brakes to replace. However the rear brake disc is also a disc / drum that houses the parking brake pads. The parking brake pads are behind the brake disc. you will have to pull the disc off to get to these brake pads. The removal of the parking brake pads requires more time and is a bit more difficult to replace. I would inspect the parking brake pads before removal and replace them only if needed.
front caliper two bolts on back of caliper one on top one on bottom remove both bolts an pull caliper up an off rotor that's all
how do i get cover off to expose bottom of radiator on 2001 buick lesabre without breaking it it in order to drain radiator how do i get cover off to expose bottom of radiator on 2001 buick lesabre without breaking it it in order to drain radiator how do i get cover off to expose bottom of radiator on 2001 buick lesabre without breaking it it in order to drain radiator
# Raise and support vehicle. # Remove the wheel and tire assemblies. # Compress the caliper # Remove the caliper slide pin bolts NOTE: Do not allow brake hose to support caliper assembly. # Remove the caliper by tilting the top up and off the caliper adapter # Support and hang the caliper. # Remove the inboard brake pad (1) from the caliper # Remove the outboard brake pad (2) from the caliper # Place an old brake shoe between a C-clamp and caliper piston. Bottom piston in the caliper bore with C-clamp. # Clean caliper mounting adapter and anti-rattle spring guide # Lubricate anti-rattle spring guides with Mopar brake grease. # Install anti-rattle spring guides NOTE:Anti-rattle spring guides are not interchangeable. # Install inboard brake pad to the caliper # Install outboard brake pad to the caliper # Tilt the top of the caliper over rotor and under adapter. Then push the bottom of the caliper down onto the adapter # Install caliper to the rotor and then install the caliper slide pin bolts, Install wheel and tire assemblies and lower vehicle, # Apply brakes several times to seat caliper pistons and brake shoes and obtain firm pedal. # Top off master cylinder fluid level.
I just did this the other day om ny 2004 silverado. Once the tires are off, remove the brake calipers. There are two "star bolts" on the rear of the caliper (top and bottom). Remove these bolts using a T-55 socket bit. Then lift the caliper up to remove it. you might have to move it back and forth to get it out of place since the pistons are compressed against the brake bads. After it is loose, you have to support the caliper so you don't put pressure on the brake lines. I used a coathanger to support it so it doesn't dangle. Just wrap the coathanger around the caliper and tie it to something underneath so it doesn't fall. Then you need to remove the caliper mounting bracket. There are 2 bolts holding this on (top and bottom). They are 18mm bolts and they are on VERY tight. I got them off using an impact wrench and hammering on an 18mm large open end wrench. Make sure you use the "box" side of the open end wrench so you don't strip the bolts. Once those are off, the caliper mounting bracket will come off and you can remove the rotor. The hardest part of this job was taking off those 18mm caliper mounting bracket bolts. Hope this helps.
there should be a alen screw through the top and bottom of the caliper that bolts the caliper to the spinle mount bracket remove those two alen screws and the caliper will lift off of the disk and then the brake pads can be removed from the caliper.