0
What size are the bolts on a 240sx alternator tensioner bolts?
Wiki User
∙ 12y ago
8mm x 1.25
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What size are the bolts on a 1995 Isuzu rodeo alternator?
The alternator retaining bolt size is 9/16. The alternator bolts will be three inches long. The alternator tensioner bolt is 9/16 by one inch.
How do you install alternator in a 1995 Thunderbird?
Type your answer here... For a 4.6l get a half inch breaker bar and insert that into the belt tensioner to loosen the belt, then disconnect the power cable (on the top of the alternator) then remove the bolts sorry can't remember what size the bolts are
What size bolts hold the alternator on a 1998 regal 2.8?
Dime sized bolts.
What size bolts on alternator for Chevy s-10?
15 millimeter and/or 13mm.
What the size of an alternator bolt for a 95 eclipse gst?
The 1995 Mitsubishi Eclipse alternator retaining bolt size is 9/16 by 3.5 inches long. There will be three alternator retaining bolts.
I want to replace the power steering belt on a Lexus Rx 330 the engine is a 3.3 liter v6?
The belt tensioner for the AC/Alternator belt is beneath the alternator. Facing the engine from bumper you can see the ac/alternator belt tensioner on the left side and beneath the alternator. Losen that bolt with size 12 socket. Next, loosen the tensioner bolt until the belt loosens. Now, with the Power Steering Belt you can loosen it by locating the belt tensioner usually found inside of the power steering belt on the power steering pump. Loosen both bolts and if needed pry UP the power steering belt tensioner and the belt should loosen. Repeat until belt comes off. Installation is the reversal of removal. NOTE: You may have to pry down the power steering pump tensioner to tighten the belt.
How remove the timing chain tensioner Chevy cavalier 2.4L?
just take the bolts out i think there size 8mm
How do you replace the alternator on a 1998 Chevy Full size truck?
first unhook the battery, then release the automatic belt tensioner and remove the belt, then unbolt the alternator and disconnect the wiring from the alternator....to reinstall, reverse the removal procedure
What drive size on a ratchet can be used to release the tensioner pulley on a 1999 ford F-150 truck?
Belt Tensioner All engines use an automatic drive belt tensioner. On the 7.5L engine, there are two belts; one uses the automatic tensioner, while the alternator belt requires periodic tensioning. On all belts using an automatic tensioner, no adjustment is necessary because the tensioner adjusts for belt wear. To adjust the tension on the 7,5L engine alternator belt, loosen the adjusting bolts and rotate the alternator until the proper tension is on the drive belt and tighten the adjusting bolts. It is recommended that the belt tension indicator mark be inspected with the engine OFF at 60,000 mile (96,000 km) intervals. If the wear indicator mark is out of specification, the drive belt is worn or an incorrect drive belt has been installed. The 4.6L, 5.4L, 6.8L, all have one belt and one belt tensioner. Look at the diagram on top of the radiator or somewhere in the engine compartment. 1/2" ratchet / or 1/2" beaker bar will do the trick.
What size bolts fit a Lincoln mark viii alternator?
The top are 8 mm and the bottom are 10 mm Remember, that is wrench size.
Lug nut size on Nissan 240sx?
The lug nut size for a 240sx with a four lug pattern is 10x1.25. The lug nut size is 12x1,25
You lost the bolts for your starter?
Depends On What The Starter Is From. Car Model Engine Size, Or Mounting Bolts Ect. If It Is The Bolts That Assemble The Starter< You Can Get These At A Starter Alternator Shop. The Mounting Bolts. Drop By The Dealer Parts House They Can Fix You Up.
