0
Posted 17 March 2009 - 03:23 PM
i was looking for this information for 4 hours "sigh"
finally found it, so for anyone that needs it, here you go
Engine specifications are the same from 1984 to 1987 for there respective engines.
Model: 4A-C
Type: 4 cylinder in-line, SOHC
Displacement: 96.8 cu. in. (1587 cc)
Bore and Stroke: 3.2 x 3.0 in. (81.0 x 77.0 mm)
Compression Ratio: 9.0 : 1
Compression Pressure: STD 163 psi @ 250 RPM, LIMIT 128 psi
HP (SAE Net): 70 HP @ 4800 RPM
Torque (SAE Net): 85 Ft./lbs @ 2800 RPM
Valve Timing:
Intake Opens: 18 BTDC
Intake Closes 46 ATDC
Exhaust Opens: 52 BTDC
Exhaust Closes: 12 ATDC
Spark Plug Type: /California /Federal
Nippondenso /W16EXR-U11 /W16EXR-U11
/W14EXR-U11
NGK /BPR5EA-L11 /BPR5EA-L11
/BPR5EY11 /BPR5EA11
/BPR5EY11 or BPR4EY11
Spark Plug Gap: 0.043 in. (1.1mm)
Firing Order: 1-3-4-2
Ignition Timing: 5 BTDC @ Max. 950 RPM (With vacuum advance off)
**NOTE** M/T and A/T in "N" range
Valve Clearance:
Intake (Hot): 0.008 in. (0.20 mm)
Exhaust (Hot): 0.012 in. (0.30 mm)
Cooling System:
Type: Water Cooled
Radiator: Vertical flow fin and tube
Radiator Cap Pressure: 10.7-14.9 psi (0.75-1.05 kg/sq. cm)
Waterpump: Centifugal v-belt drive
Thermostat Valve Opening: 190 F (88 C)
Capacity: 5.9 qt. (5.6 liter) M/T
With Heater: 5.8 qt. (5.5 liter) A/T
Fuel System:
Type of Carburetor: Downdraft, 2 Barrel
Fuel Pump: Mechanical Diaphragm
Fuel Pressure: 2.5-3.5 psi (0.18-0.25 kg/ sq. cm)
Fuel Filter Type: Paper Filter Element (flow through)
Fuel Tank Capacity: 13.2 gal. (50 liter)
Fuel Grade: USE UNLEADED FUEL ONLY (Research Octane No. 91 Anti Knock
Index 87 or Higher)
Lubrication System:
Type: Mechanical
Oil Pump: Gear Type
Oil Filter Capacity: 0.3 qt.
Recommended Motor Oil: API grade SF or better
Oil Capacity /w Filter: 3.5 qt. (3.3 liter)
Electrical System:
Battery (volts/ amp hours): 12V/50A - hr
Alternator (volts/ amps): 12V/55A
Starter Motor (volts/ kW): 12V/1.0 KW M/T - 12V/1.4 KW A/T
Add your answer:
Earn +20 pts
Valve clearance specs for Wisconsin engine?
inlet 6 though, outlet 8 though
What are the torque specifications for a 2002 Chevy Malibu 3.1 engine?
what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.
What was the 1947 Ferrari's performance and engine specs?
the engine specs is tat it runs on poopys
What are the cylinder head bolt torque specs for a 1.9 D Peugeot engine?
i need the head torque settings for peugeot 1.9 diesel motor
Can no muffler hurt the motor?
it really depends on the motor specs but yes it can because the muffler not only reduces engine noise it also provides enough back pressure for your vehicle to runs more efficient
What are the torque and rod specs for a Chevy 3500 series 5.7 liter motor?
The torque specs. are 45 Ft- lbs. If its a 1991 engine its 20 FT-lbs first then turn each nut additional 60-degrees.
What are the timing and dwell specs on a 1983 Toyota Corolla with a 4AC engine and a vacuum advance type distributor?
timing: 5 degrees btdc. electronic ignition sets dwell automatically. timing: 5 degrees btdc. electronic ignition sets dwell automatically.
What is the timing specs 1996 Ford F-250 5.8 engine?
timing specs 96 5.8 engine
1994 fxrp engine specs for motorcycle?
1994 harley Davidson cop bike, i need engine specs
What is the recommended motor oil for 2012 VW Passat with a gasoline engine?
You need to use an oil meeting VW 502.00 specs. Mobil 1 SAE 5w-40 meets those specs so that is what I would recommend you use.
What are the torque specs for a Honda gx120 motor?
rod
How do you check your compression on your engine?
You can go to auto zone and borrow one of their compression tools, it screws into where the spark plug goes and reads compression as the motor turns over. You will need the specs for that particular motor which i am sure they can provide for you.
