0
Remove the 3 screws from the black panel above the passengers feet. Remove the 8 screws from around the panel that holds the glove box. (4 top and 4 bottom)
Take a flat head screwdriver and pop off the upper right side panel.(The panel on the side of the upper right AC vent.) You will see one last screw with a tab, holding the glove box panel. Pull out and down a little and the panel will come off. Unplug the speaker wire 2 pin connector.
Now you will see the white box that holds the blower motor. On the bottom of it, you will see one black screw that holds a rectangular box approx. 4x2". unscrew it to get it out of the way. Unscrew the passenger side floor to door carpet, foot panel.(4 screws) Unscrew the "plastic" screw in the upper corner of the right plastic triangular floor panel, then pull out the plastic spacer.
Pull up the rubber door molding on the lower door frame about one foot. Take a flat head screwdriver and and pop the triangular panel off. On the lower right of the blower motor, attached to the right wall, you will see a metal heat sink. (It has 3 connectors attached to it) There are 2 bolts on the bottom attaching it to the side and a metal tongue groove on the top. Unbolt it and slide it down and out. You don't have to unplug the wires. Again this is for easier access. (At least for my big hands.)
On the bottom front of the blower motor you will see a black board with 3 connectors. This is the blower motor resister. The middle connector goes to the motor. Unhook it. To the right of it is another connector that goes to the other side of the motor and is resting in the white frame. Unplug it.
There are 3 gold screws on the bottom of the blow motor assembly. Take a stubby screw driver and unscrew them. Disconnect the small black plastic air hose. Wiggle the blower motor and fan cage out.
Take the new motor assembly and do in reverse.
Add your answer:
Earn +20 pts
How long does it take to replace blower motor 1992 Chevy truck?
About 15 mins. That's a easy job.
How do you replace blower motor on a 1992 Buick Century with the power steering reservoir and pump in the way?
You may have to vmove them to get at it
Heater blower will not work on 1992 Mazda 626. already replaced resistor block.?
You probably need a blower motor. Check the Hot electrical feed to the motor. If you have replaced the resistor block you know where the motor is located (just to the right) It is easy to replace and can be purchased everywhere, including a junk yard. Remember some Resistor Blocks fail because the motor is old and drawing to many amps.
Where is the blower motor on a 1992 buick regal gran sport?
The blower motor on a 1992 is located under the hood. It is on the firewall on the passenger side.
Replace blower motor on 1992 Mercedes 300e?
under the hood.. by the windshield wipers.. it blows in .. doesn't suck through.
Do you need to take off the dash to replace blower motor in a 92 town car?
( No ) The blower motor is in the engine compartment . It is near the firewall towards the passenger side of the engine compartment in a 1992 Lincoln Town Car
Where is the blower motor resistor located in a 1992 Honda accord?
It is located on the blower motor housing and is white in color. You have to take the blower motor assembly out as far as I know to get to it.
How do you change a blower motor on a 1992 Toyota Camry?
The blower motor is on the passenger side underneath the dash. Its not hard to get too. It has 3 or 4 screws and it takes a little manipulation to get it out but its a simple job. Took me about 30min. to remove and replace it.
How can you remove and replace a blower motor on a 1992 Lincoln Town Car without having to remove the antifreeze reservoir?
If the reservoir is blocking the way, then it will have to be removed.
Why does heater blower on 1992 s10 run on high only?
Probably the blower motor resistor is shot.
Where is the blower control resistor located on a 1992 Ford Explorer?
under the blower motor housing. to the right
Does a 1992 dodge ram 350 van have a relay for the blower motor?
Yes. First check to see that you have 12 volts to the blower motor. If yes, blower motor has probably failed. If no, it may be the blower motor relay or there is a speed control resister pack causing your problem.
