1.) Remove the screw that is behind the inside door handle. It has a small plastic cover that you need to pry off with a small screwdriver.
2.) Remove the screw that is directly under the pull-handle (the part you pull to close it) of the door. There is a small piece of sticky rubber that you need to remove. It just peels off. It'll stick right back down again when you're done.
3.) Remove the screw that is underneath the door light. You need to pop the cover off to expose the screw. (if there is screw, because only US models has it)
4.) Move the Tweeter. I can't recall how to do this off the top of my head, but it's not hard. I think you just need to pull it out. (if you have the tweeter)
5.) Remove the inside plastic piece behind the door handle. It just slides over the handle.
5.) "Pop" the door panel free. There are about 9 clips around the perimeter of the panel that pop free with a moderate amount of force. You also need to push the door light through the hole at the bottom while doing this step.
6.) That should be it. The door panel should be free of the car.
2015 models have no door light screw. Definitely buy a vinyl trim tool. The kit I bought was a Dorman set from auto zone. Well spent 17.99.
remove door panel, remove speeker.
Nobody knows.. Or they wont tell you... Have to take it to the mazda dealer...
i have a 2004 Mazda 6, and the first thing you do is you have to remove the door panel which is held on by plastic anchors and typically 3 screws so just pull out then up once the screws are out. then next you need to pull hard on the little black door tweeter (just plastic anchors) then its a simple unscrew and plug in and put the tweeter then door panel back on. the plastic anchors will still be good afterwards.
1. Open window & remove door lock knob. 2. Remove 2 screws from armrest & remove armrest. 3. If manual windows, remove windoe crank. 4. Pry under & remove trim panel around door handle, remove any un-covered screws. 5. This is the fun part, the door panel is affixed with plastic retaining clips, slip something thin under door panel until you can feel where clip is and pull door panel away from door at that point. These clips are suppose to remain in the door panel, but rarely do. They usually remain in the door itself. do this for EVERY clip you find, there are clips approx a foot apart around the entire panel. Good luck. 6. After all retaining clips are pulled out, lift panel slightly to disengage panel from flange at base of window. 7. Disconnect any electric wires or switches and there you have it. Try not to curse.
i got the same car. remove the door panel there will be two screws in the inside door handle and like 6 or 5 aound the outside edge of the door panel remove all these and then pull and pop the tabs loose all around. and pull the whole panel upwards off the door
This is the same front or rear door. 1. remove rubber insert at the bottom of the arm rest/door handle2. remove the 2. Philip head screws.3. run hand along bottom edge of door panel to ensure no other securing screws. 4. starting at the top rear edge of the door panel side a large flat screw drive/door panel tool(what ever you have) 5. lift sharply and you will here poping noises fromt the push clips lifting out of the socket.6. as you work down the rear edge of the door panel you will see the trim around the interior door handle lift away. remove it.7. the interior door handle will remain on the door. 8. remove the rest of the door panel.
Inside the passenger-side door on the right side of the dash there is a panel (6"x6"? Rounded corners. Remove panel.
1. Remove the wing mirror cover 2. Remove the screws to remove the door handle 3. Remove the door handle, but this is a little tricky and you might break a clip on the handle due to it being tight against the dash, carefully does it 4. Remove the 2 seat retaining bolts 5. Un-clip the seat front mounts and move the seat so you can gain access to the door panel lower screws 6. Now carefully remove the door panel ,once away from the door, slide out the door panel clips, so you don't scratch the door post trim, also be careful to ease the panel around the door speaker itself 7. Now slide the door panel in between the seat and the door through to the rear of the car 8. Remove the inside door lever (the one you use to open the door from the inside) and its control bar, there is no need to remove the bar from the lock.
1. Remove the wing mirror cover 2. Remove the screws to remove the door handle 3. Remove the door handle, but this is a little tricky and you might break a clip on the handle due to it being tight against the dash, carefully does it 4. Remove the 2 seat retaining bolts 5. Un-clip the seat front mounts and move the seat so you can gain access to the door panel lower screws 6. Now carefully remove the door panel ,once away from the door, slide out the door panel clips, so you don't scratch the door post trim, also be careful to ease the panel around the door speaker itself 7. Now slide the door panel in between the seat and the door through to the rear of the car 8. Remove the inside door lever (the one you use to open the door from the inside) and its control bar, there is no need to remove the bar from the lock.
easier than you think .remove two press pins in end of door (one top,one bottom).Remove snap panel behind arm rest and removetwo screws with #15 torx driver. Remove outer snap panel around door handle. Use care and pry snap pins all around lower door panel( 6). Door panel will lift right off. Thanks this will also help a lot with the replacement of the rear window vent (quarter window)
Remove all 6 screws from the door panel, 3 on the very bottom, 1 by the arm rest where your hand go's,1 in the cup of the handle to open the door, 1 on top where there might be a tweeter (little speaker) is and after removing all screws pull the door panel out & up a bit to give space to stick your hand in between panel and door to disconect the 2 rods that link the handle and door lock and finally off with the door panel to expose the speaker.
Assuming you are talking about the door speakers, (1)remove the door trim panel; (2)remove the screws securing the speaker to the door; (3)lift out the speaker and disconnect the electrical connector at the speaker. (4)Installa tion is the reverse of the removal steps. To remove door trim panel, (1)remove the window regulator handle (if equipped with power windows, remove the switches by removing the screws for the power window switch and the other connectors on the back side of the door trim finish panel); (2)remove the screws from the armrest area of the door panel; (3)remove the inner door handle; (4)remove the screw (if equipped) at the lower rear of the door panel (5) lift the panel at least 1-1/2 inches to disengage it from the slots along the bottom of the door, then remove it; (6)if necessary, carefully peel the watershield from the door being careful not to tear it; (7)installation is the reverse of the removal steps. - Haynes Ford Ranger Pickups Repair Manual