0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you remove back seat of Kia Rio?
Removing the back seat in the Kia Rio is simple. Remove the screws or bolts from the lower cushion and remove cushion. Then remove the now visible screws and remove the remaining parts.
Camry overhead console removal?
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
How do you remove the door that holds the headlight blinkers and parking lights there are no visible screws?
You have to remove the chrome bezel and possibly the grill depending on the model.
How do you remove the instrument cluster in a 1993 Toyota Camry?
It is not difficult. First you have to remove the 12vot cigarette lighter plastic and then remove the radio. 4 screws for the radio. Then you have to remove the panel that goes from the radio up to the instrument cluster. This panel has 4 screws. 2 of them are on top of the instrument cluster (visible) and the other two should be visible after removal of radio.
How 2 unlock front door ie lost key?
i am assuming this is a legal access. the most feasible is to unlock from inside, unless you are talking deadbolt, then remove screws from inside, remove knob, and use screwdriver to disengage bolt, you may have to twist the little square hole. Once door is open take entire lockset to hardware where they can make you a new key or sell you a new deadbolt. i hope this helps
How do you remove heater metrix from Skoda felicia?
You first empty the glove box. Next you remove the pins holding the glove box and snap it out. The screws are now visible loosen and remove the matrix.
How do you remove the front sight on a Winchester model 70?
Only 1 screw is visible, there are 2. Remove front sight hood, drive dove tail blade out from left to right. The other screw is visible now. Remove both screws and the ramp comes off.
How do you remove the stereo in a 1995 Mitsubishi diamante?
you have to remove the center console there are four screws in each coner of it if you tri to remove it by releasing the two screws under the cup holder and you pull ti you will break the dash because there anre two screws that are not visible from the outside just remove the center console then youwill see a couple of more screw and you will get to the radio good luck and be pacient
How do you disassemble overhead console in 94 Chevy Suburban?
Remove the screws that hold the headliner in place. With the headliner removed the overhead console retaining bolts will be visible. Remove the retaining bolts. Remove the wiring harness from the console.
Steps to install a smart lock on your front door?
First, you need to remove your old lock. As you have access to the door and its keys, start by locating the screws on the interior of the lock and unscrew them. You would be able to remove the locking mechanism from the inside. On the outside, the key assembly would be loose, pull that off from the front. On the side of the door, there’s the bolt that slides out to secure the lock. Locate and remove the screws with the help of a screwdriver. You can now pull out the old lock. With the new lock bolt, you usually get a new deadbolt, strike plate, and other miscellaneous hardware. To start with, you could install these pieces with the help of a screwdriver and a few other tools. First, install the strike plate and deadbolt. If the holes are smaller than the screws, you may need to drill a little until the strike plate and deadbolt are firmly in place. Next, you need to install the front and back of the smart lock. For this, you will need to make sure the parts are aligned correctly. Check the how-to-install brochure to make sure you’re doing it right.
How do you replace the instrument panel bulbs in a dodge ram 2500?
Remove the instrument panel cover retaining screws. There are four screws that need to be removed. The instrument panel light bulb's will be visible. Push the light bulb in and turn at the same time to remove the light bulb.
How do you removed tail lights 2002 Ford Expedition xlt?
two screws are visible when the tail gate is open. remove these screws and pull on the light distribute the pressure. the clips will let go with a little pull. remove wire harness from the light housing by counter clockwise turn.... two screws and 4 clips per light
