0
It was an old way to lower cars, you'd have to cut a coil off the bottom so that the spring end is in the same place in the spring perch( hacksaw or cut off wheel-NO
torching). For safety reason it is not recommended, since the spring rate is the same, the chance of bottoming out is high. The spring also might have softened up due to age/usage. Most cars have aftermarket spring available that increase the rate to prevent this, this is the route I'd recommend.
Add your answer:
Earn +20 pts
If you replaced the air bags with coil springs how do you turn off the suspension light on a 2000 Lincoln town car?
google it, there will be direction to cut a certain wire to make the light go away. There will be no damage done by doing this.
Can you cut suspension springs on car and still be legal?
Lowering of cars is not typically illegal. It's putting a lift kit on them that can cause you problems with the law. This is all because the headlights have to be a certain height off the ground and can't be too high as you could blind the driver coming at you in the opposing lane. Coil springs yes, leaf springs no.
Can you lower 96 Buick riviera?
yes you can lower any car, cut the springs
How do you lower a car?
there a few different possibilities depending on your car and budget. first you have to decide what suspension type you have - the three main suspension types are coil spring, torsion bar and/or leaf spring. to lower coil spring suspension you just buy replacement springs, or if your budget will stretch that far go for adjustable platform suspension. (alternatively you can get your angle grinder out and cut them - but not recommended) with leaf springs you can buy lowering blocks which go in between the spring and axle, lifting the axle up into the body of the vehicle, thus lowering it (cheap option) the better (and dearer option) is to get the leafs reset which flattens them, thus lowering the vehicle. and finaly, torsion bars - the more complicated type to lower. some cars you can wind them up(or down) by using a ratchet to wind up a bolt, or another type requires you to remove the spline from the suspension and rotate the shaft a couple of splines, and put it back together, lowering the suspension.
What will cause your 325i BMW to cut off?
There are many things that can cause a car to cut off. Lack of electricity throughout the car, lack of fuel through the fuel system, and parts not being connected or firing correctly.
If your new coil springs making your car sit high should you cut a coil?
never never cut a coil spring---firstly the ends of springs are tapered to sit flat on there mount secondly coils are made of very tough material so you would have to put a lot heat to them (cutting torch or chop saw)to cut into them thirdly they will settle after a few miles are put on the car anywayDepends on what you're talking about. New OEM springs & about 1/2 to 3/4" higher, just wait. Springs settle about a half inch over the first few months. Also, it's possible that your car was sagging because the old ones were worn out.Lowering springs, vs. old lowering springs or OEM? Can't help if you're compairing to old lowering springs, but if you're compairing to OEM, you probably have the wrong part.i wouldn't cut the springs to lower it if it is sittin to high buy coilovers for it so you can adjust your ride height and it will also stiffen up the ride for tight cornering( have had coils cut on cars before and it is a big headache if not done perfectly)
How do you disable the air suspension light on a 2000 Lincoln town car when it was converted to springs?
I'm sorry I don't have the exact details...but when my 95 TC was converted to springs, an instruction sheet came with the spring kit that addressed the issue. There was a small circuit board located behind the glove box in the dashboard, and one cut one of the wires from it. Darn shame I don't remember which wire, but maybe this hint will help you research further.
How do you disconnect the air suspension light from a 1999 Lincoln town car?
cut the middle wrie on the shut off swith. 4from left or 4 from right
How do you drop a Mazda Protege?
Cut your springs...
How do you lower a 1984 Mazda B2000?
The 84 is not as easy to lower as the later models because it has coil springs in the front and newer models have torsion bar suspension. To lower an 84 you can cut the coil springs shorter and install lowering blocks in the rear. You can also remove the rear leafs and have the de-arched. Do not cut the springs with a torch as this will ruin the temper and they will collapse, instead use a cut off wheel. Another way to lower the front is with drops spindles or control arms but I do not know if any are made for the 1st gen trucks. After cutting the front springs the truck will require a front alignment to bring you're camber and toe into specs, if you don't you will eat through tires quickly. Kyrasis6 Owner of Mazdatruckin.com
How do you cut coil springs on a camaro?
bad idea- just buy lowering springs. it's alot safer for everyone!
How do you cut an emergency brake line on a 1992 ford thunderbird?
crawl underneath and find a metal cable that leads from the middle of the car to the back to both rear brakes, it should have some springs in it and its probably rusty, cut it with a bolt cutter or a dikes
