yes you always glue on the tiles first. or what ever you are using. then i would wait a 24 hrs to dry. then you can do the grouting.
If you stain with a breathable stain such as from SANSIN Corporation, you may coat anytime. If you're sealing it, you should wait until the moisture content is at least 12%. I can't tell you how long to wait because that depends on the humidity, temperature, how long it has already been cut etc.
a day to make sure
It should tell you on the can as every paint is different.
you should let them dry for 2 to 3 hours before you wear them
if you mean dry enough to seal, most grout companies suggest about 20 to 30 days. most grout will dry enough to walk on in a day
Yes - but you are always best off removing a large portion of the old grout before re-grouting. After letting the new grout dry for 48 hours, consider using a grout sealer to make it last longer.
Contarary to popular mis conception you are not sealing the tile as much as you are sealing the Grout. The finish on the tile is a Glass glaze & really needs no sealer... Go to the Home Depot or Lowes & tell them you are looking for a good Tile grout sealer & then just read the instructions or visit their website for the video.. It ain't rocket science, any one can do it.. PLEASE make sure you start with clean & Dry Grout though, otherwise you are just sealing in the mold, mildew & stains.. Do web search for Aqua mIx used to be a great product, I think it is still avail
It all depends on the sealer you used! I use a product called StableCrete that penetrates into the grout joints to waterproof them without leaving a film. Ready for light traffic in four hours. The Grout is what you seal with a ceramic install and not the ceramic!
You will need a grout saw and grout scraper to remove the old grout. Then use an epoxy grout meant for swimming pool use, and work in small areas at a time. Choose a color that matches the tiles. Follow the mixing instructions on the container. When all the tiles are properly filled wait for it to dry before finishing the job with a sealant.
Depending on the tilesetter, but typically a couple days. The floor needs to be prepared and if there was any patching it may need to dry. The tilesetter may want to come back the next day. Then the tile needs to be set and if the tilesetter has good tools that should only take an hour or two. Then the mortar needs to set before the tilesetter can do the grout. Grouting should take most of a day since the grout needs to cure while it is being cleaned. You should not walk on the tile while the grout is setting up and sealing the grout should wait for a few days. The time involved isn't so much a funciton of the size of the tile job, but more a function of the mortar and grout setting times.
Grout can dry different colors due to inconsistent mixing, uneven drying conditions, or the use of different batches of grout. It can also be affected by the absorption rate of the tiles or surfaces it is being applied to, resulting in variations in color.
yes you always glue on the tiles first. or what ever you are using. then i would wait a 24 hrs to dry. then you can do the grouting.
Brown grout that dries white typically results from improper mixing or water content during installation. It could also be due to a reaction with the air or existing grout residue on the tiles. It's recommended to follow manufacturer's instructions carefully and ensure proper mixing techniques for consistent color.
You can get grout stain. It will let you make it darker. If you want to change the grout altogether then it can be easily removed, but time consuming. Simple grout removal tools are available at local home stores. Also a oscillating multifunction power tool will make quick work of it. Then re-grout the joints in whatever color you choose. Grout charts are available where grout is sold. Remember grout will look darker when being installed and will dry lighter. Be very careful of making sure everything is clean. Vacuum out old joints with a wet/dry shop vac. If you use a power tool to remove grout have someone follow behind it with a shop vac. Or you will have dust everywhere.
"Grout is the stuff you apply between tiles to seal them in place. Grout tiles once the adhesive has dried fully (24 to 36 hours later). The best grout is waterproof and mould-resistant; some come ready-mixed. Use a grout float - a rubber-faced tool with foam backing - for large areas. Spread the grout across the tiles at right angles to the joins. Use a damp sponge to remove excess. Once the grout is dry, polish the surface with a dry cotton rag." I was taught by a contractor to apply and clean the grout diagonally.
Clorox wipes typically have a shelf life of about one year before they start to dry out. Factors such as exposure to air and sunlight can accelerate the drying process. Properly sealing the container after each use can help extend the lifespan of the wipes.