0
Add your answer:
Earn +20 pts
How to remove an ignition control module on a 1996 Nissan Altima?
The ignition control module is located within the distributor housing, so you need to remove the distributor, which is held in by two bolts, remember to slack off the valve cover bolts around the distributor, this facilitates the removal process, don't worry about the valve cover gasket it's an o-ring type gasket so it will reseal itself when you tighten the valve cover bolts .
What is the cost to replace the transmission in 1996 Chevrolet truck?
it cost 1500 dollars to replace my tranny at the local tranny shop
How do you replace a hydro booster on a 1996 Chevrolet 2500 series truck.?
remove the silly clip that holds the brake pedal and brake light switch on the pushrod, try not to damage the clip. Remove the four bolts around the brakepedal pushrod hole.(inside, these are tough to get at, a 3\8 air ratchet makes it much easier). remove the two bolts that hold the master cylinder to the booster.Pull the cylinder off booster. do not remove any brake lines, there is enough flex in the lines to get the job done. remove the three hydraulic lines from the booster. You might have to pry a little to get the pushrod off the pedal. remember the wire hanger on the cylinder bolts when you put it back together. Once the pushrod is back on the brake pedal it goes together really easily
How do you remove a broken starter bolt on a 1996 Toyota Camry 4-cylinder?
get a tap and die set and follow the instructions.
Why does parking brake light remain on in a 1996 Ford Escort when parking brake is off?
The light may be the low fluid level for the master cylinder also. Check the fluid level.
How do you remove the starter in a 1996 Chevy 2500 diesel?
how to remove starter on 1996 chevrolet 2500 with 6.5 diesel engine
How do you change a tail lightbrake light on 1996 Chevrolet 1500 pick up?
open tailgate, use #2 Philips scredriver and remove the 2 screws that hold the light assembly in, carefully remove light from box corner, unplug main harners from light, unscrew the circuit board on the back of the light remove and turn over, replace bulb and reinstall.
1996 Toyota Camry valve cover gasket?
how do i remove the valve cover to change the gasket in a toyota camry 1996
How do change headlight bulb on 1996 Chevrolet truck?
Remove battery, remove horn, remove wire, twist bulb counter-clockwise to remove.
How do you remove bumper cover from 1996 blazer?
rip it off
How do you remove the gearbox arm on a 1996 Chevrolet 1500?
Ever try a steering arm puller?
How do you Replace a valve cover gaskets in 1996 buick regal custom?
remove motor mount "dog bones" and also label/remove spark plug wires from spark plugs, remove valve cover, clean cover from debris, use light coat of oil to stick gasket, replace round rubber gaskets, replace cover, wires and "dog bones"
How do you change the rear brake and signal light in a 1996 corolla?
Lift up the trunk and next to the rear light cover you want to take off, where the trunk comes down there are 2 screws. remove them. take the carpet off on the wall in the trunk opposite to the rear light cover. in the middle of that back panelthere is a nut connected to a bolt. remove it. the rear light cover should come off. where the lights go into the cover they are labeled for what their purpose is and what color the bulb. to remove the bulb just twist the bulb holder and it should come out of the light cap. reassemble the parts in reverse order
How do you remove ignition switch on 1996 Chevrolet Tahoe?
Chevy Tahoe Ignition Key Starter Switch
How do you remove valve cover on 1996 caddilac?
The valve cover on a 1996 Cadillac is held on by several bolts around the edge. After removing any hoses, fuel rail, or anything else in the way, remove the bolts to pull the valve cover off.
Why does the ABS light turn on on a 1996 Chevrolet Camaro?
usually a bad wheel sensor, get it checked out.
1996 3.1 liter GM do you need to remove the oil pan in order to remove timing cover?
No.
