Remove the plastic horn section of the steering wheel by gently put firmly pulling each 'spoke' of the plastic about 1 inch in from the edge of the wheel. Lift each spoke only slightly, then move to the next spoke to release them all, don't try to pull on just one or two. Disconnect the push on connector(the horn) and put the plastic horn piece aside. You should see a nut in the center, about 4 inches down. As I recall, this is 23mm, but not sure. Remove it. Place the steering wheel so that front wheels are straight and spokes of wheel are pointed horizontally (to line it back up when reinstalling). Now alternately bump each side of the steering wheel from the bottom of the wheel with the palms of your hand. The wheel will slowly ride up the splines of the shaft and come off.
remove the battery and wait for 5 min .remove the 2 screws that holds the covers just below the steering wheel to have more access to the holes at the back of the wheel, use a short flat screwdriver to flip a spring wire while pressing the top, and do the other side. The top of the wheel should pop out
4 bolts are romoved from the backsode of the steering wheel. If airbag equipped remove airbag fuse first. Then remove airbag/ horn/ center assembly. Remove large nut from center of wheel, then pull wheel with steering wheel puller.
hopefully your not stealing the vehicle. but you will have to remove the steering wheel and then remove the key switch itself, purchase a new key switch and replace. However if its only to move the vehicle, after you remove the key switch you can take a screw driver and turn the mechanism in the column to unlock.
You will need a puller to remove the steering wheel, after you remove the nut and snap ring in the center of steering wheel. Ther are two holes in the wheel that are threaded. Install puller on center shaft, and screew 2 long bolts through the puller and into the holes on wheel.
Park the truck with the front wheels in the straight ahead position do not turn or the steering wheel shaft after,before or during or will damage the clockspringDisconnect the negative battery cable and wait at least 2 minutes for the airbag capacitor to discharge before proceedingIf the truck is equipped with speed control remove the switch retaining screws.Pull off the switches and unplug the electrical connectorIf equipped remove the right rear steering wheel cover using a small screwdriverRemove the 4 nuts attaching the airbag module it will probably be necessary to turn the steering wheel to gain access to the nuts; just be sure to center the wheel after the nuts are removedLift off the airbag module and unplug the electrical connector when you set the airbag module down make sure the airbag side is facing up so that if it accidentally deploys it wont launchRemove the steering wheel retaining nut and mark the position of the steering wheel to the shaft if marks don't already exist or don't line upUse a puller to detach the steering wheel from the shaft don't hammer on the shaft to dislodge the wheel
It is located behind the steering wheel. You will need to remove the steering wheel. Its a blak circular part that has a 3-5 wire plug in the back of it.
To remove the steering wheel in a 1988 Chevy Celebrity standard version: !. Remove the screws that hold the horn pad in place then remove it. Unplug the wire at the connector. 2, If it still has the safety clip remove it. 3, Use the appropriate wrench to remove the nut from the steering shaft. 4. Use a steering wheel puller to loosen then remove the steering wheel. Reverse the instructions to replace the steering wheel. Steering wheel retainer nut should be 30 ft. lbs. torque.
A person needs a steering wheel puller to remove a steering wheel. It will help remove the steering wheel by putting pressure on the middle and by pulling up on the rest of the steering wheel.
To remove the steering wheel from your 1985 Chevy Celebrity: First remove the horn button. There should be a keeper at the tip of the steering shaft, remove it. Remove the nut that holds the wheel in place. Use a steering wheel puller to actually remove the steering wheel.
Local car part stores have a tool called the steering wheel puller, that has to be used to remove the steering wheel. This is used to remove the steering wheel by applying pressure to the middle and pulling up on the rest of the steering wheel to remove it.
Disconnect battery. Remove air bag. Remove bolt holding steering wheel to column. Use a steering wheel puller to remove wheel from column.
first take of the cover if you have one it will be round or a sideways H, take out the bolts that are holding the horn on, then take the bolts out that are holding the steering wheel in place.
It can be hard to remove a steering wheel by hand on any vehicle. To remove it, there is a tool, steering wheel puller, that can be bought or rented from local auto shops. It will help remove the steering wheel.
Steering wheels are hard to remove. A tool called a steering wheel puller needs to be used to remove the steering wheel. It removes the steering wheel by applying pressure to the middle and pulling the rest of the wheel up.
How do you remove steering wheel daewoo lanos
PROPERLY remove air bag (if equipt), then remove nut holding steering wheel on and then use a steering wheel puller to remove it.
You can remove the steering will, on your Ford Ranger pickup truck, by removing the steering wheel pin. Remove the wiring harness and the steering wheel will come off.
Removing a standard steering wheel from a Chevy Cavalier requires taking off the lower steering column and horn button. The steering wheel is held on by mounting screws, after removed be sure to unplug the horn wire.