0
I am guessing this is on the floor. This is probably a two component carbon bond coating. This means it is chemical resistant to even ketones. To recoat, you must use another epoxy or urethane mixture. To prepare the surface, it must be wet sanded with at least 220 grit water paper. After a good sanding, the surface must be cleaned with some sorta tack cloth. If you use a waxed based tack, do not press hard. This will cause transfere of the bees wax to the surface and cause poor adhesion. Anyway, get the surface clean as possible. Make sure the humidity is below 50% before coating the area. If you try to coat with humidity aboue 50%, you may get bubbles in your coating. They are caused by the coating trying to cure quicker than the moisture can escape. I hope you can use this information.
If it is a true epoxy coating that is on the floor, and it is not coming up anywhere, you can clean the area with a pressure washer and degreaser, then you can put a two component epoxy on top of it, I recommend two coats, 24hours between coats.. one of the best on the market is Benjamin Moore 2 component polyamide epoxy. If it is subjected to uv rays you need to top coat the epoxy with a two component aliphatic urethane.
Epoxy can be applied over nearly any existing finish; however, what is being painted should be sanded lightly with 200 or finer grit paper prior to painting so that the new paint will bond better.
I,v got over 20 years inpainting. application, you know...learned it the hard way. painting over epoxy is always tricky.( I,m talking about the two part epoxy) if you start with epoxy and stick with epoxy, usually you'lldo just fine. any kind of latex paintwill lift off of epoxy. oil paint will stick a bit longer, but that's coming up to.thewhole point of epoxy is to have nothingstickto its surfaceso thatit cleans easy.you can try and strip it, messy and time consuming. now your mixing chemicals. one tip.. take a piece of sand paper, sand a small area. if what you sanded leaves dust.. I would paint that. if balls up or rolls? its the same as painting over rubber. hopes this helps.
Yes youcan. However, the existing epoxy paint should be sanded to "rough" it up to make the new paint stick to it better.
Paint over it with another paint containing particles like crushed walnut.
Add your answer:
Earn +20 pts
Can a bathtub be painted?
Yes, with a special enamel used for that purpose. ------------------------------ Yes, it is best left to a professional to paint it electrostatically with epoxy enamel (or other) paint. They do it in your home without having to move the tub. It not expensive.
What type of paint do you use to cover epoxy primer?
Almost any kind, including epoxy enamel.
What paint can you use for inside a bath?
A marine enamel or an epoxy paint is your best bet. However I wouldn't expect any paint to last in a bath.
Can you use latex paint over an epoxy painted wall. and what steps are needed?
You can definitely use latex paint over epoxy. In fact, it is recommended to use latex over epoxy by the paint manufacturers, rather than using epoxy over epoxy. The latex adheres better and if you then want to use epoxy next time you paint, you have a nice coat of latex between the layers. If you use epoxy over epoxy, often the paint will just peel off in layers once some time passes (and sometimes right away).
Can you use enamel spray paint to paint a bathtub?
Enamel paint can be used on porcelain or iron bathtubs with great results, so I'll walk you through this process, just in case you're unsure about how to do this.You Will Need These MaterialsWhite vinegar WaterTowel Palm sander 150-grit sandpaperRespirator mask Plastic bag Tape Epoxy enamel spray paint Oil based primer Oil based enamel paint 1200-grit wet/dry sandpaper InstructionsClean the bath tub thoroughly with a mixture of white vinegar and water. The vinegar will help remove any dirt or greasy residue on the tub. Rinse the tub to remove the vinegar and dry it with a towel.Equip a palm sander with 150-grit sandpaper. Sand the inside and the outside of the tub to roughen the surface, this will allow the paint to properly adhere to the bathtub.Remove the fixtures of the bathtub or cover the fixtures with a plastic bag. Tape the bag down at the base of the fixtures to prevent painting them when you paint the inside of the tub.Spray the inside of the bathtub with an epoxy enamel spray paint such as Krylon epoxy enamel paint. These paints are available at most home improvement stores and will resist moisture which is necessary for paint on the inside of a bathtub.5 Paint the outside of the tub with an oil based metal primer such as Rust-Oleum metal primer. Let the primer dry completely.Apply a coat of oil based enamel paint to the outside of the tub. Let the first coat of paint dry and then apply a second coat.Sand the second coat of paint with 1200-grit wet/dry sandpaper used wet. This will help shine the enamel paint.I hope this helps you out with your project! Good luck!--The Violet
Can a bathtub be painted?
Yes, with a special enamel used for that purpose. ------------------------------ Yes, it is best left to a professional to paint it electrostatically with epoxy enamel (or other) paint. They do it in your home without having to move the tub. It not expensive.
What type of paint do you use to cover epoxy primer?
Almost any kind, including epoxy enamel.
What paint can you use for inside a bath?
A marine enamel or an epoxy paint is your best bet. However I wouldn't expect any paint to last in a bath.
Can you apply epoxy over painted garage?
As long as none of the paint is flaking, you can.
Is your painted steel bowl oven safe?
A painted steel bowl is oven safe, as long as the paint is enamel.
Was 1986 Chevrolet pickup painted with laquer paint and if so what sort of paint can i use without going down to bare metal?
Factory finish would have been an enamel paint. Even if it has been repainted, it is most likely enamel also. If the paint is old you can probably paint it with anything without it raising the old finish. If in doubt, you can spray a sealer on first and then the paint.
Can you use latex paint over an epoxy painted wall. and what steps are needed?
You can definitely use latex paint over epoxy. In fact, it is recommended to use latex over epoxy by the paint manufacturers, rather than using epoxy over epoxy. The latex adheres better and if you then want to use epoxy next time you paint, you have a nice coat of latex between the layers. If you use epoxy over epoxy, often the paint will just peel off in layers once some time passes (and sometimes right away).
Can you use enamel spray paint to paint a bathtub?
Enamel paint can be used on porcelain or iron bathtubs with great results, so I'll walk you through this process, just in case you're unsure about how to do this.You Will Need These MaterialsWhite vinegar WaterTowel Palm sander 150-grit sandpaperRespirator mask Plastic bag Tape Epoxy enamel spray paint Oil based primer Oil based enamel paint 1200-grit wet/dry sandpaper InstructionsClean the bath tub thoroughly with a mixture of white vinegar and water. The vinegar will help remove any dirt or greasy residue on the tub. Rinse the tub to remove the vinegar and dry it with a towel.Equip a palm sander with 150-grit sandpaper. Sand the inside and the outside of the tub to roughen the surface, this will allow the paint to properly adhere to the bathtub.Remove the fixtures of the bathtub or cover the fixtures with a plastic bag. Tape the bag down at the base of the fixtures to prevent painting them when you paint the inside of the tub.Spray the inside of the bathtub with an epoxy enamel spray paint such as Krylon epoxy enamel paint. These paints are available at most home improvement stores and will resist moisture which is necessary for paint on the inside of a bathtub.5 Paint the outside of the tub with an oil based metal primer such as Rust-Oleum metal primer. Let the primer dry completely.Apply a coat of oil based enamel paint to the outside of the tub. Let the first coat of paint dry and then apply a second coat.Sand the second coat of paint with 1200-grit wet/dry sandpaper used wet. This will help shine the enamel paint.I hope this helps you out with your project! Good luck!--The Violet
Why can't you use any spray paint for metal on a refrigerator?
I can't say why, but they do make an Appliance Epoxy spray paint.
My garage is already painted. Do I need to remove paint before adding the quikrete Epoxy Garage floor coating?
It is best if you do remove the old paint first.
What paint do they use for playground equipment?
maybe yellow , red and blue's primary colours are good for that sort of thing :)
Can you paint over enamel with latex?
you can paint over latex paint with latex enamel.
