answersLogoWhite

0


Best Answer

i have a 87 Dodge Dakota v-6 pick upat the bottom of the bell housing there are 2 bolts one on each side that hook to a bracket.that hooks to the moter.remove both bottom bolts,you will be able to move and bend the bracket on the starter side out of the way,also will be able to pull the sheet metal gauard from the lower half of the bell housing out.take the top and bottom bolts out of the starter you will need to twist and turn the starter to get it out.but its not all that bad.that is the way i did mine hope this was some help to you Dave

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Can't remove 1987 dodge Dakota starter with V-6?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

What could cause the starter not to work in a 1987 Dodge Dakota 4 cylinder?

Make sure battery is charged. Clean all wire connection at battery & at the starter. Make sure trans is in neutral or park completely or clutch pedal is completely depressed (check if neutral switch is ok) If no response from these check out solenoid, starter 7 innition switch & all wires/connectors in starting circuit. Here is another thing to look for-make sure the ground strap is connected to block & frame/body. Check the fuse & relay. They are located in the fuses box on the fender well in the engine compartment


Starter location 1987 cressida?

Under the Throttle Body


Where is the starter in a Chevy Corsica?

the starter is on the passenger side of the engine compartment under the vehicle is the way to access it . First remove neg battery cable . then go to the starter itself and remove the pos bat cable and starter solenoid wire inspect the back of starter to see if a support bracket is installed remove the bracket as necessary. next remove the two 9/16 head bolts and dropthe starter . also there may be a stiffiner stut in the way that may have to be removed as well


How do you replace a starter switch in a 1987 Chrysler LeBaron Town and Country Turbo with a tilt wheel?

There is a solonoid on the starter and the ignition switch is on the steering column.


Where can i get a Ignition coil wiring diagram for 1987 dodge ram 50?

It is important to have wiring diagrams on hand. A person can get an ignition coil wiring diagram for a 1987 Dodge Ram 50 in the maintenance manual.

Related questions

Will a 1987 Dodge Dakota automatic fit a 1998 Dodge Dakota 5 speed?

no, probably not


What is the fuel mileage for a 1986 dodge Dakota with a V6?

The Dodge Dakota did not come out until 1987


A diagram for a 1987 dodge Dakota 3.9 v6 power steering system components?

how do i put a power steering pump on a 1987 dodge Dakota truck v6


Where is the orifice tube located on 1987 Dodge Dakota?

A 1987 Dakota uses an expansion valve, not an orifice tube.A 1987 Dakota uses an expansion valve, not an orifice tube.


How do you change the starter on 1987 blazer s-10 with manual trans?

Remove the positive battery cable from your 1987 Chevrolet Blazer battery. Remove the starter cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.


What other year model Dodge Dakota have interchangable parts with a 1988 Dakota?

1987 to 1990 should be similar


Where is the wiper motor on 1987 dodge Dakota?

under the hood near the wipers


Where is the windshield wiper fuse located on your 1987 Dodge Dakota?

in a fuse block


Towing Capacity for a 1987 Dodge Dakota V6 3.9 liter?

Many vehicles have many more specifications added when the vehicle is produced. The towing capacity of a 1987 Dodge Dakota V6 is up to 5,500 pounds.Ê


Where are the timing marks for a 1987 2.2L dodge Dakota?

The timing marks on a 1987 2.2L Dodge Dakota are located on the timing chain and the cam sprocket. They must be perfectly aligned to prevent the pistons and valves from hitting each other.


How do you replace the starter on a 1987 Ford E-150 Econoline Van?

Disconnect the - battery cable Raise and support vehicle Remove wires at top of starter Remove starter mounting bolts Remove starter


How do you remove a starter from a 1987 Chevy 350 small block?

remove grn from bat. remove bat cable from starter solinoid. remove brn wire from starter solinoid. remove two 3/8bolts from starter to block. tilt nose of starter up and lower. this is most common.