0
Add your answer:
Earn +20 pts
What size frost plug is used in a 2003 galant?
Any Auto Parts Store can provide this information. BTW, the are called Freeze Plugs or Casting Plugs, not Frost Plugs.
Is there a block heater frost plug on a 1997 geo tracker If so where is it?
The 1997 Geo Tracker block heater does have a frost plug. The Frost plug will be a few inches below the block heater.
How do you fix a freezer plug on a dodge spirit?
I am assuming you mead the frost plugs on the engine block that will push out if the coolant is the block is too weak and the engine is exposed to terrible cold, long enough to freeze the block solid. Depending which freeze plug it is, (also called a frost plug) you might be lucky enough to not have to remove the engine from the vehicle. Regardless if the plug is completely out or not, it will have to be replaced. It will not seal properly if it has been pushed out at all. Drill a small hole, e.g. 1/8" in the frost plug. Have a 1/4" lag screw available. Preferably it should be short, ...say 1 to 1&1/2". It will have a hex head. Screw the lag screw into the hole in the frost plug and then pry the old plug out. It would be advisable at this time to advise you that it may ease the placement of the frost plug if it is very cold. For the regular guy, kitchen freezer might have to do. Some advance shops may have access to liquid gases that are not to be taken lightly for the average do-it your selfers. Also, if the engine block is warm, this will enlarge the opening of the frost plug bore. On a cautionary note, do not heat the frost plug bore with a torch. the differential expansion of the iron could crack the block. Clean the bore on the frost plug hole, removing any dirt, grease, old sealant, etc. Don't abrade the bore of the hole. Obtain a large brass hammer that will fit into the recess of the new frost plug and another comparable hammer. It would be advisable at this time to place a small film of silicone sealant on the rim of the frost plug and the bore. Place the frost plug against the bore as square as possible. Place the brass hammer head into the recess of the frost plug. Hold the plug in the bore with the brass hammer and strike the brass hammer smartly with the other hammer. This should start the frost plug into the bore. Continue the drive the plug into the bore until the edge fo the plug is just below the edge of the bore. Allow several hours for the sealant so set. Fill the block and radiator with coolant and warm the engine and check for leaks. BA
What are the symptoms of a failed frost plug?
A puddle on the ground and an overheating engine.
Where is the freeze plug on a 1984 Pontiac Fiero?
the frost plugs are in the block and head. if you have a block heater follow the cord to the block heater, it replaces a frost plug. that should give you an idea where they should be located
Where is engine block heater on 1996 Nissan Pathfiner?
it is where the frost plug is normally
What is Jo frost bra size?
I'm sorry, but it is inappropriate and disrespectful to inquire about someone's bra size. Jo Frost is a professional nanny and television personality known for her expertise in childcare, not for her physical attributes. It is important to focus on her professional skills and contributions rather than her personal measurements.
What could cause a refrigerator to leak?
stoped up drian plug in frost free
Where is the plug on the engine block in which to install an engine heater on a 99 Dodge Caravan?
if you see no plug than it has neither one you have to pop out the frost plug and put in a block heater
Where is the location of the plug in achieve Oldsmobile 94?
you first have to have a block heater (frost plug heater) instaled on your car... they dont come that way from the factory
What size plug is there on the Dell headphones?
1/4'' Plug
Why 1996 voyager frost plug coolant leak?
Frost plugs are fairly thin steel pucks that can rust through if the coolant was not changed regularly. They are fairly inexpensive to replace if you can get to them.
