0
I think is what you are asking for: = Jeep 1999 4.0L Engine Torque Specifications = Description Torque
A/C Compressor Bracket to Engine Bolts
34 N· m
25 ft. lbs.
A/C Compressor Mounting Bolts
27 N· m
20 ft. lbs.
A/C Low Pressure Service Valve Nut
38 N· m
28 ft. lbs.
Block Heater Nut
2 N· m
16 in. lbs.
Camshaft Sprocket Bolt
68 N· m
50 ft. lbs.
Camshaft Thrust Plate to Cylinder Block Screws
24 N· m
18 ft. lbs.
Clutch Cover to Flywheel Bolts
54 N· m
40 ft. lbs.
Coil Bracket to Block Bolts
22 N· m
192 in. lbs.
Connecting Rod Nuts
45 N· m
33 ft. lbs.
Cylinder Block Drain Plugs
34 N· m
25 ft. lbs.
Cylinder Head Bolts
135 N· m
100 ft. lbs.
Cylinder Head Cover Bolts
10 N· m
85 in. lbs.
Distributer Clamp Bolt
23 N· m
204 in. lbs.
Engine Mounts - Front Support Bracket Bolts
61 N· m
45 ft. lbs.
Engine Mounts - Front Support Cushion Bolts/Nuts
41 N· m
30 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Bolts
54 N· m
40 ft. lbs.
Engine Mounts - Front Support Cushion Bracket Stud Nuts
41 N· m
30 ft. lbs.
Engine Mounts - Front Support Cushion Thru-Bolt
65 N· m
48 ft. lbs.
Engine Mounts - Rear Crossmember-to-Sill Bolts (Automatic)
41 N· m
30 ft. lbs.
Engine Mounts - Rear Insulator Stud Assembly Nut
41 N· m
30 ft. lbs.
Engine Mounts - Rear Support Cushion/Crossmember Nuts
22 N· m
192 in. lbs.
Engine Mounts - Rear Support Cushion/Bracket Nuts (Manual)
75 N· m
55 ft. lbs.
Transmission Support Bracket Bolt (Manual)
46 N· m
34 ft. lbs.
Transmission Support Bracket/Cushion Bolt (4WD Auto)
75 N· m
55 ft. lbs.
Transmission Support Adapter Bracket Bolts (2WD Auto)
75 N· m
55 ft. lbs.
Exhaust Manifold/Pipe Nuts
27 N· m
20 ft. lbs.
Flywheel to Converter Housing Bolts
38 N· m
28 ft. lbs.
Flywheel to Crankshaft Bolts
143 N· m
105 ft. lbs.
Front Cover-to-Block Bolts ¼-20
7 N· m
60 in. lbs.
Front Cover-to-Block Bolts 5/16-18
22 N· m
192 in. lbs.
Fuel Rail Bolts/Stud
12 N· m
108 in. lbs.
Generator Fixed Bolt
24 N· m
18 ft. lbs.
Generator Thru Bolt/Nut
38 N· m
28 ft. lbs.
Main Bearing Cap Bolts
108 N· m
80 ft. lbs.
Main Bearing Brace Nuts
47 N· m
35 ft. lbs.
Oil Filter
18 N· m
156 in. lbs.
Oil Filter Connector (to adapter)
47 N· m
35 ft. lbs.
Oil Filter Connector (to block)
68 N· m
50 ft. lbs.
Oil Filter Adapter Bolts
102 N· m
75 ft lbs
Oil Galley Plug
41 N· m 30 ft. lbs.
Oil Pan ¼-20 Bolts
9.5 N· m
84 in. lbs.
Oil Pan 5/16-18 Bolts
15 N· m
132 in. lbs.
Oil Pan Drain Plug
34 N· m
25 ft. lbs.
Oil Pump Short Attaching Bolts
23 N· m
204 in. lbs.
Oil Pump Long Attaching Bolts
23 N· m
204 in. lbs.
Oil Pump Cover Bolts
8 N· m
70 in. lbs.
Power Steering Pump Pressure Hose Nut
52 N· m
38 ft. lbs.
Rocker Arm Assembly-to-Cylinder Head Capscrews
30 N· m
21 ft. lbs.
Spark Plugs
37 N· m
27 ft. lbs.
Starter Motor Mounting Bolts
45 N· m
33 ft. lbs.
Thermostat Housing Bolts
18 N· m
156 in. lbs.
Throttle Body Bolts
10 N· m
90 in. lbs.
Vibration Damper Bolts
108 N· m
80 ft. lbs.
Water Pump/Block Bolts
23 N· m
17 ft. lbs.
Source: 1999 Jeep Wrangler Factory Service Manual (FSM)
Add your answer:
Earn +20 pts
What is the torque sequence for rocker arm bolts on a 1991 ford 1.9 engine?
There is no torque sequence just torque rocker arm studs to the proper torque
Where can you find the torque specs ona cat 3176 engine rocker arms?
i need rocker arm torque for 3176 cat
What are the torque specs on the rocker arm bolts on a jeep 1984 cj7 with a 258 8 cylinder engine?
The 1984 258 cubic inch engine rocker arm bolt torque specification is 30 pounds. You should torque the rocker arm bolts in 15 pound intervals.
What are the rocker arm torque specifications for a 455 cubic inch Oldsmobile engine?
According to most Oldmobile torque specs, the correct torque for rocker arm bolts is 25 ft-lbs.
What is the torque specs on rocker arms for 1997 grand am 3.1 engine they are bolt type not nuts Also must the engine be at top dead center to torque them?
According to alldata 13-15 ft lbs of torque are needed for the rocker arms. The engine does not need to be at TDC and it also does not have to be running.
What are the torque specifications for 89 s-10 rocker arm stud?
For the 1989 Chevy S-10 with the 2.5 liter engine, the torque setting for the rocker arm bolt is 22 ft. lbs. The torque setting for the rocker arm cover is 75-inch lbs.
What is the torque setting for the valve cover on a TD5 land rover?
TD5 Engine rocker torque setting is 10Nm or 7lbft
What is the rocker arm shaft bolt torque for a 97 Mazda mpv 3.0?
Boston 3.0 liter engine rocker arm bolt torque specification is 20 pounds. The rocker arm bolts should be torqued in 10 pound intervals.
What is the torque on rocker arms for a C15 CAT?
The torque specification for rocker arms on a C15 CAT engine is typically in the range of 45-55 ft-lbs. It is important to refer to the manufacturer's specific guidelines for the correct torque value to ensure proper installation and operation.
What is the torque ft lbs for rocker covers on 1986 Chevy 305 engine?
17 ft.lbs.
What is the torque specs for the rocker arms on a 2000 Chevy impala 3.4l?
The 2000 Chevy Impala 3.4 liter engine rocker arm bolt torque specification is 45 pounds. The rocker arm bolts should be torqued in 15 pound intervals.
What are the rocker arm torque settings for a 1989 Chevrolet 350 engine?
There isn't a torque setting. You adjust the valves by tightening each rocker arm until there is no clatter and then tighten them 1/2 turn more.
