0
There all kinds of tools for Ball Joints; OTC Remover, Ball Joint OTC Ball Joint Separator KD Tools Ball Joint Separator OTC Ball Joint Service Set KD Tools Universal Ball Joint Separator OTC Wrench, Ball Joint Spanner KD Tools Ball Joint/U-Joint/Brake Anchor Pin Press OTC Master Ball Joint Adapter Set KD Tools Ball Joint/U-Joint/Brake Anchor Pin Press Set KD Tools Ford Ball Joint Cam Tool Sears.com
Add your answer:
Earn +20 pts
How do you change a lower ball joint that is pressed in?
To change a lower ball joint that is pressed in, you need to use a ball joint press tool to remove the old joint from the control arm. First, detach any components securing the ball joint to the control arm. Next, position the ball joint press tool over the joint and apply pressure to push it out. Finally, install the new ball joint by pressing it in using the same tool.
How do you remove a lower ball joint from the control arm in a 1990 Ford Thunderbird?
Hey Tina==sometimes you need a special tool to separate the ball joint. Check with your parts store as sometimes they have them for rent. Goodluck, Joe
How do you remove lower ball joints on a vw beatle?
In the Standard Beetle the ball joints are pressed into the trailing arms. You need a special press tool to replace these. In the Super Beetle the ball joint is part of the lower control arm, you replace the arm when the ball joint is worn out.
Removal of lower front ball joint on a 1994 ford aerostar van?
With a ball joint press and removal tool.
How do you replace all ball joints on a 01 F250 2wd with twin I beam suspension?
First, remove the wheel and brakes and then steering knuckle from each side. Then, for each knuckle, use special tool to press each ball joint out of the knuckle. Use same tool to press new ball joint into place. Reassemble. Or, if you don't know how to do any of that, go to a good mechanic.
How do you replace the ball joints on 1997 E-350 Van?
From: http://en.allexperts.com/q/Ford-780/Ball-Joint-Replacement.htm Ball Joint Replacement [Ford Van] Remove the brake disc. Remove the wheel speed sensor. For additional information, refer to Section 206-09. Remove and discard the cotter pin and nut. Disconnect the tie-rod end. Remove and discard the cotter pin and the nut. Remove the pinch bolt adjuster. CAUTION: To prevent damage to the ball joint seal and the ball joint socket, do not use a pickle fork-type remover to loosen the ball joints. Remove the front wheel spindle. Strike the lower end of the front axle to loosen the ball joint. Remove the front wheel spindle. To install, reverse the removal procedure. Check and, if necessary, align the front end. Remove the wheel spindle assembly. For additional information, refer to Wheel Spindle - E150-E450 in this section. Position the front wheel spindle in a vise, and remove the snap ring from the lower ball joint. CAUTION: To avoid damage to the components, do not use heat to aid ball joint removal. Using the special tool and suitable receiver cup, remove the lower ball joint from the front wheel spindle. Using the special tool and suitable receiver cup, remove the upper ball joint. Installation CAUTION: To avoid damage to components, do not use heat to aid installation. NOTE: Clean the wheel knuckle ball joint bores. NOTE: The lower ball joint must be installed first. Using the special tool with suitable receiver cups, install the lower ball joint. Using the special tool with suitable receiver cups, install the upper ball joint. Install the snap ring in the groove at the bottom of the ball joint. Install the front wheel spindle.
How do you install a ball joint on 2001 dodge stratus?
You have to use a special tool to press it in. Mine just popped out last night. The original factory ball joints are junk. Aftermarket are much better quality.
How do you replace ball joints in a 1995 Pontiac grand prix?
You will need a special tool to pull the old joints. Most auto parts stores will loan the tool for free. The rest is simple. Just install the same way the old came off. (The only to get the joint off is to get the special tool)
How do you replace ball joints on a 97 Ford Thunderbird?
The ball joints on a 97 Ford Thunderbird are replaced by placing the vehicle on jack stands, removing front wheel and rotor, and unbolting the steering knuckle. A ball joint puller is then used to remove the ball joint and a special installer tool is used to press the new one into place.
What does a ball joint splitter do?
It is a tool mechanics use to separate the ball joint from the bracket or steering knuckle. The ball joint stud is tightened into a hole that is tapered (morse taper). Removing the nut will not separate it without force.
How do you replace ball joint on 1995 BMW 325is?
They are pressed in/out with a special tool that looks like a big c-clamp, they can be done on a press,but is more work/takes longer.
What are some tricks in removing a separated ball joint?
If you mean a broken ball joint, you may need a cold chisel and hammer or air grinder to remove the steel rivets and a tool called a "pickle fork" to drive between the ball joint and the spindle to separate the ball joint from the spindle taper after removing the cotter pin and nut.
