answersLogoWhite

0


Best Answer

Check your local library for repair manual, you can photocopy what you need.

User Avatar

Wiki User

βˆ™ 15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Show you a Timing diagram for a 1990 3.3L v6?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How many oz in .33L?

33 litre of water is 1,164.042 ounces


How do you replace the front lower ball joints on a 1995 Intrepid ES 33L V6 automatic?

You can't service the lower ball joints by themselves. You must replace the entire lower control arm.


Where is the fusible link located in a 1989 Buick Century 33L Engine?

thir is on the hot wire that is conected to the startter and one that runs off relays behind right head light and one behind fues box in dash


How do you adjust the idle on a 1999 Plymouth Grand Voyager 33L?

Everything is set by the computer. If its not idleing right it is probably a throttle body sensor or a idle control sensor or a number of other things. You need to have it hooked up to the computer to check the codes.


How do you replace the lower ball joint on a 1991 Plymouth Voyager LE 33L and if special tools are needed what are they?

you need to press them in.if you put your ball joints in the freezer overnight they will shrink.Then heat up your a- arm with a torch and use a jack to pop the frozen ball joints in


Where is the horn located on a '93 Pontiac Grand Am SE 33L V6?

On the bottom front passanger side, near side of radiotor - I have a 94, but it's probably the same. There are two horns, one on the left, the other on the right. You have to remove the mud guards that are right in front of the wheels and right behind the bumper. They are a pain to get to and work with.


Ca a 38L engine in a 1994 Chrysler Town and Country Van be replaced with a 33L engine from a later model year?

Well, the transmissions are interchangable, so your good there. But if you put a 3.3l in youll have to change the ECM because they have different settings for the 3.8 and 3.3. So if you change the ECM I think youll be ok. My email is RPplayer73@aol.com


2006 Grand Caravan 33L - when in park engine won't rev above about 3000 rpm No warning lights and drives just fine and engine gets up to 4500-5000 rpm Is rpm limit in park by design or a malfunction?

For most newer vehicles this is normal. It puts unnecessary wear on an engine to rev it high in park/neutral.


How many oxygen sensorsare there on a 1995 intrepid 33l If two is it the same type sensor?

Well, on my 1996 'trepid with the 3.3L, there are four sensors. [Note - My 3.3L is equipped with the California Emissions so it may be different] The upstream sensors are the same, but they differ from the downstream sensors. Considering that the catalytic converters for the 1995 and 1996 are the same, I would expect you to have the same number of sensors.


Where are the oxygen sensors located on a 1999 dodge grand caravan sport 33l v6?

Let me guess you have a service engine soon light on and the computer is saying it's your Oxygen sensors. Oxygen sensers are normally located on the exhaust pipe, within 12 inches of the exhaust manifold, you will probably have to get underneath the van to see them. I think it's just emissions stuff nothing real important


Why would a 93 Pontiac grand am se 33l v6 engine click while running?

i would check the harmonic balancer the rubber seal on it probably has come off and you need to lift up the engine to get to it check your oil level... if its low then that could be your problem, if its not low then it could be one of a few things. best case senario, its low oil, worst case, rod knock if your oils fine and it keeps getting worse...have a mechanic look at it.


Where can you get instruction for installation of the belt tensioner on a 1999 Dodge Caravan 33L?

from underneath the vehicle after the belt has been remove use a 15mm or 5/8 deep well socket (can't remember), a long extension and a swivel. place the socket on the back of the tensioner you should be able to feel around and locate it. then position the ext. w/ swivel on the socket hit the ratchet to the left/ up and loosen the bolt. use your right hand to hold hte tension and your left to unscrew the nut..