0
On high voltage transmission lines how can you estimate the voltage transmitted based on the number of insulators used?
Count the number of stacked "rings" on the insulator and multiply by 10kV; this will give you a rough estimate. THAT IS B.S. TRANSMISSION IS 500KV SO YOUR FRIEND WANTS 50 OF THOSE B.S. THAT IS NO CORRELATION TO THAT. BUT DISTANCE IS A VERY GOOD FACTOR TRUST ME ON THAT.
Add your answer:
Earn +20 pts
How can measure the voltage only seeing the insulators in a high voltage transmission lines?
i think 11kv per insulator
What is long rod insulator?
High rod insulators are used for the insulation of medium and high voltage transmission lines. Long rod insulators meet IEC standards and are rated up to 800 kV.
Why suspension insulators preferred for high voltage power transmission?
'Suspension' type insulators are less expensive to manufacture than 'pin' type insulators for voltages in excess of around 33 kV. Each 'dish' is designed for specific voltage (e.g. in the UK, typically 11 kV), and several can be added to form a 'string' to match any desired voltage level. This inceases their versatility. Suspension insulators also allow for greater lateral movement of the conductors.
Why is the alternating current voltage increased?
In order to be transmitted long distances, voltage is raised. At the destination, voltage is lowered again to be used. This permits transmission for several miles, which wold not be possible at lower voltages.
What is the voltage range at which power is transmitted?
CSA C235-83-CAN3 Preferred Voltage Levels for AC Systems, 0 to 50,000 V Electric Power Transmission and Distribution
High voltage current is needed for transmission but is low voltage is more useful?
A: Power transmission is in the range of 500 kilo volts as someone can tell the hi towers are far above ground and each phase is separated by ceramic insulators. Low voltage is necessary to manage these power safely to homes and business. That is why transmission becomes distributions and finally local power to us.
How are electrical insulators made?
The insulators used on high tension transmission lines and on distribution lines are made of either glass or ceramic shaped in a mold. On high tension lines several are typically stacked to create a compound insulator that can avoid arcing at the voltage on the lines.
Information or data is transmitted in digital computers by voltages that are switched on or off?
voltages must be on before data information can be transmitted in digital computers and not so when using the internet, because the message is transmitted at the slightest glimpse of power source. does not need proper voltage to carry out transmission
What is the use of insulators on transmission lines?
The same reason insulation is used on electrical wire.The voltage at which transmission lines are operated, can produce serious short circuits, if two of the lines make contact, and depending on the system, can arc to the ground (earth). This can cause serious injury or death if a person happens to be in harms way.If you examine these line insulators, you will find there are many "hills and valleys" on the surface of them. This is to increase the "creep" length of the insulator and total distance between conductors and ground.At this high voltage, the current will arc for some distance.In general, insulators are for protection of the continuity of the power supply to the system's users.
What are the two basic categories of transmission?
The two basic categories of transmission are:High voltage transmission andLow voltage transmission.
What does a transformer do to a voltage in a power line?
A transformer is used to step up (increase) or step down (decrease) an alternating voltage with very little loss of energy.
How to calculate the the number of insulators used in a transmission line?
The glass, 'dish', ('cap and pin') insulators used to support conductors from transmission towers are each rated to withstand a specific voltage. But this voltage depends upon the standards used by the electricity industry of the country in which you live but, typically, they are each designed for operating voltages within the range 10 - 12 kV. By dividing the effective line-to-earth value of the transmission voltage, by this value, you will be able to determine the the 'basic' number of dishes required. This figure, however, will only be a guide, as the voltage gradient across the string of insulators is not linear. Furthermore, additional dishes are sometimes required according to the environmental conditions affecting the transmission line. For example, if the line is near the coast, the dishes might be subject to salt deposits; if the transmission line is near industrial factories (e.g. steel works) then the line might be subject to deposits from airborne waste from those factories, etc. So, often, the number of dishes will be greater than that number required to provide the basic insulation level.
