0
How do you successfully get the belt tensioner bracing bracket off of 1991 Chevy G20 350 van thermostat housing?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is the thermostat on an infinity qx 4 1999 and how hard is it to change?
Follow the lower hose to the engine. The thermostat is in the water outlet behind the bracket the AC belt tensioner is mounted. Removing this bracket and the fan shroud makes this an easy job.
How do you install a serpentine belt and tensioner for a Plymouth voyerger?
You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.
How do you change the tensioner on a Plymouth Voyager minivan 1996?
You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.
How do you remove replace the tensioner on a 96 3.3 liter Caravan?
You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.
1996 Jeep Cherokee Tensioner Pulley?
There is no tensioner pully. The Power Steering pump has a moving bracket that adjusts the belt tension. It has a long adjustment bolt. You have to remove the air cleaner and housing to reach it successfully. Funny, mine has a belt tensioner pulley under the power steering pump, which is tightened by a long adjustment bolt. So does every other 1996 Cherokee I've worked on!
How do you release Fan Belt tensioner On Peugeot 206?
Use a 3/8"extension bar to lever the tensioner ( there is a corresponding whole in the bracket that the tensioner pivots on).To hold it in position theres a whole where you can inset a bolt.
Where is thermostat on 89 ford 7.3 diesel?
behind fuel bracket
How do you replace the thermostat on a 1987 nova?
Look at the large tube coming out of your radiator. Where that attaches to the engine there is a bracket that clamps to the hose and bolts on to the block. Take the bracket off the block. Inside of this is where the thermostat sits.
How to replace the alternator on a 1993 Dodge Grand Caravan fully loaded?
3.3L and 3.8L Engines The 3.3L and 3.8L engines were equipped with the Nippondenso alternators. 1. Disconnect the negative battery cable. 2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner. 3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it. 4. Remove the alternator tensioner/power steering bracket bolt. 5. Remove the tensioner stud nut and remove the tensioner. 6. Remove the alternator mounting bolts. 7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way. 8. Remove the alternator support bracket bolts. Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine. 9. Remove the alternator from the engine and disconnect the electrical leads. To install: 10. Install the alternator in position on the engine and connect the electrical leads. 11. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm). 12. Install the power steering reservoir on the mounting bracket. 13. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm). 14. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold. 15. Install the alternator belt, insert a 1/2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt. 16. Connect the negative battery cable.
Belt tensioner assembly on a jeep?
it is under the power steering pump attached to the bracket that holds the pump.
How do you change a serpentine belt on a 1996 cadillac concours deville?
loosen the tensioner bracket, remove old belt. replace with new belt. tighten with tensioner. job complete!
How do you adjust the serpentine belt on a Kia Sephia?
It depends if you want to adjust the belt that does the a/c and power steering, or the one to the alternator. The power steering goes this way. First loosen the hex screw running through the power steering pump bracket. Then loosen the bracket hex screw that attaches to the belt tensioner bolt under the power steering pump. Then, tighten the tensioner hex screw that runs through the tensioner bracket. After you finish the adjustment, tighten all hex screws. If you adjust the belt for the alternator. You must loosen the alternator bracket hex screws on both the top and botom of the alternator. This requires going under the vehicle. Then, loosen the tensioner bracket hex screw and adjust the tensioner hex screw that runs through that. When you get the propper tension, tighten all screws and you are done.
