0
There isn't a manual way to set timing on 2.5L engine. It's controled by the crankshaft and camshaft sensors. Most all OBD2 systems are this way regardless of type of car. If the question was for how to put the car in time cause the timing belt is off then the question wasn't answered. That would and does have a certin way to go for everything to work together and not to get a piston to valve slap. Carefully remove the timing cover. Be careful not to distort or damage it while pulling it up. With the cover removed, check the immediate area around the belt for wires and other obstacles. If some are found, move them out of the way. Align the timing marks on the camshaft's sprocket with the mark on the cylinder head. If the marks are not obvious, use a paint stick or chalk to clearly mark them. Carefully remove the crankshaft timing sensor and probe holder. Loosen the adjustment bolt on the belt tensioner pulley. It is normally not necessary to remove the tensioner assembly. Slide the belt off the crankshaft sprocket. Do not allow the crankshaft pulley to rotate while doing this. To remove the belt from the engine, the crankshaft pulley must be removed. Then the belt can be slipped off the crankshaft sprocket. After the belt has been removed, inspect it for cracks and other damage. Cracks will become more obvious if the belt is twisted slightly. Any defects in the belt indicate it must be replaced. To begin reassembly, place the belt around the crankshaft sprocket. Then reinstall the crankshaft pulley Make sure the timing marks on the crankshaft pulley are lined up with the marks on the engine block. If they are not, carefully rock the crankshaft until the marks are lined up. With the timing belt fitted onto the crankshaft sprocket and the crankshaft pulley tightened in place, the crankshaft timing sensor and probe can be reinstalled. Align the camshaft sprocket with the timing marks on the cylinder head. Then wrap the timing belt around the camshaft sprocket and allow the belt tensioner to put a slight amount of pressure on the belt. Adjust the tension as described in the service manual. Then rotate the engine two complete turns. Recheck the tension. Rotate the engine through two complete turns again, then check the alignment marks on the camshaft and the crankshaft. Any deviation needs to be corrected before the timing cover is reinstalled.
Add your answer:
Earn +20 pts
How do you set the timing on a 1996 2 5 Chrysler cirrus?
This is something you cant do manually!It is controlled by sensors!
How do you set the timing on 1996 Chrysler Sebring 2.5L 6 cylinder?
If you are asking about ignition timing there is no adjustment it is controlled by the engine controller
Where is the re-set button on 1997 Chrysler cirrus after car has been in a collision?
Chrysler does not use inertia/reset switches.
How do you set the timing on 1994 Chrysler?
Timing can not be adjusted, is done by the PCM.
How do you set the timing on a Honda accord 1996 V6?
Timing is set by the ECU.
Can the timing be set on a 1996 Nissan 4x4 with a 4 cylinder engine or is it electronic?
Yes the timing can be set.
How do you set the ignition timing for a 1996 Mazda Protege and what is the correct timing?
Hoo I set the correct timing on a 1993 mazda protege
How do you set the timing on a 2005 chrysler 300?
look in owners manual if not in there sorry
How to set timing on 1996 Toyota Tercel?
you cannot adjust the ignition timing on this car. a manual will help if you need to set cam timing
Do you need a timing light to set your 1996 suburban?
NO. A timing light will not work on that engine. You must have an obdII engine scanner to set the timing on that year.
How do you set the timing on an 1985 and 1989 Chrysler 318 that has no timing degree makers on the block but there is a line in the balancer?
I'd just set it by ear and how easy it starts once it's set.
Gghow do you set the timingon 1996 Kia Sportage?
already answered. see: how do you set the timing on 1996 kia sportage ?
