0
Open up the paneling to the Right side of the stering wheel. Then unbolt the rear access panel with a 5 mm torx wrench. When the panel is removed you will find 2 red wires, 2 green wires, and a single blue wire. Cut this wire and solder in a 3.3 kohm resistor. Now activate the voice control feature and say " reset trip meter " in traditional Chinese. Your trip meter is now reset.
Add your answer:
Earn +20 pts
How do you reset the trip meter on a 2001 jeep?
Press and hold the trip reset button while you are on the trip meter.
How do you reset the mileage counter on new Ford Fiesta?
Hi, to change it between the total miles and the trip meter you need to hold down the tube-like switch.....and to reset the trip meter you press it once (when you're looking at the trip meter - not the total miles)
How do you reset your speedometer on your 1999 Honda Civic EX Sedan?
You cannot reset a speedometer. You can reset the trip meter but not the odometer. Reset the trip meter by pushing and holding the trip button.
How do you reset trip meter?
There is usually a reset button.
How do you reset trip meter 2003 Windstar?
Push the reset button just to the right of the trip odometer
How do you reset trip meter for suzuki xl-7?
What year is the vehicle? On my 2006, there is a button beside the little window at the bottom of the speedometer. Short presses cycles between odometer, trip meter 1 and trip meter 2. While displaying the trip meter, press and hold the button for about 2 seconds. The trip meter will reset to zero.
How do you reset odometer on 2011 dodge ram?
You can not reset the odometer. The trip meter can be reset by holding down the button.
How do you reset the maintenance required light on a Toyota Venza?
Resetting the maintenance LightSwitch the display to the trip meter A when the engine is running.Vehicles with smart key system:Turn the "ENGINE START STOP" switch off.Vehicles without smart key system:Turn the engine switch to the "LOCK" position.Vehicles with smart key system:While pressing the trip meter reset button, set the "ENGINE START STOP" switch to IGNITION ON mode (but do not start the engine because otherwise the reset mode will be canceled).Continue to press and hold the trip meter reset button until the trip meter displays "000000".Vehicles without smart key system:While pressing the trip meter reset button, set the engine switch to "ON" position (but do not start the engine because otherwise the reset mode will be canceled). Continue to press and holdthe trip meter reset button until the trip meter displays "000000".
How do you turn off the maintenance light after you change the oil on a 2004 Solara?
Step 1 Turn the key to the 'on' position. Step 2 Reset both trip meters to zero. you can reset the trip meters to zero by selecting trip A or trip B and holding in the trip meter button for five (5) seconds. Step 3 After both trip meters are reset, select any trip meter and hold in the trip meter button and start the car. Step 4 Continue holding the trip meter button until the "maintenance required' light disappears. Have Fun, King Geoff
How can i set my camry's speedometer to zero for a new trip?
You are referring to the trip meter right? My 2004 trip meters reset by turning the ignition key to accessory and then hold the reset button sticking out of the bezel in for several seconds. It will reset to 0. Same for the other trip meter if your car has two. The speedometer odometer cannot be reset except by an authorized facility. It is against federal law to reset a speedometer odometer.
How do you reset the service light on the s40?
Turn ignition key to the 1st position, and then push and hold the trip meter reset stem, then, while continuing to hold the trip meter pushed in, and after no more than 2 seconds, turn the ignition key to the 2nd position and continue to hold the trip meter reset pushed in until the service light begins flashing. Once it begins flashing, you can release the trip meter. You may also get an audible signal when complete.
How do you reset the service light on a Volvo S40?
Turn ignition key to the 1st position, and then push and hold the trip meter reset stem, then, while continuing to hold the trip meter pushed in, and after no more than 2 seconds, turn the ignition key to the 2nd position and continue to hold the trip meter reset pushed in until the service light begins flashing. Once it begins flashing, you can release the trip meter. You may also get an audible signal when complete.
