answersLogoWhite

0


Best Answer

get on the bottom of your car and push the ignition cylinder out

This works on '94's and newer...well, at least up to '04.

Step #1 is very important if you don't want your air bag to blow...

  1. Disconnect the neg. cable from the battery, disconnect the pos. cable from the battery, wait 2 minutes.
  2. Turn the ignition switch to RUN.
  3. Insert a 1/8 inch punch up through the little hole in the trim under the lock cylinder (you don't need to take any plastic off), hold the punch in while you pull out on the key. You should be holding the lock cylinder in your hand now.

Installation is almost the reverse (your battery is still disconnected, I hope):

  1. Push in the locking pin on the side of the new cylinder and turn the key so the cylinder is in the RUN position.
  2. Install the cylinder into the housing--fully seated and aligned with the interlocking washer.
  3. Turn the key to OFF. This lets the pin pop back out and lock the cylinder in place.
  4. Test the key by turning it from OFF to START. If that checks out, go to step 5 otherwise go back to 2.
  5. Reconnect the battery, Pos. first, then Neg.
User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the ignition cylinder on a Mustang?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you remove ignition tumbler 1998 Ford Mustang?

How do you remove ignition tumbler 1998 ford Mustang?


How does the ignition cylinder come out on your 91 Buick century?

Remove the ignition cylinder retaining ring. Poll the ignition cylinder out. Remove the wiring harness from the back of the ignition cylinder.


How do you remove the ignition key cylinder from a 2003 Kia Optima when a key broke off in the cylinder?

You will need to remove the retaining ring at the top of your 2003 Kia ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness from the back of the ignition cylinder.


How do you remove ignition cylinder from 1975 Chevy pickup?

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.


How do you remove the ignition lock cylinder on a 1997 astro van?

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.


How do you remove the ignition lock cylinder on a jaguar x-type?

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.


How do you remove the ignition cylinder on a 97 Chevy 1500 WT when it is frozen in the lock position?

Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.


How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.


How do you get ignition cylinder out on 1999 mystique?

You can change the ignition cylinder on your 1999 Mercury Mystique by removing the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness.


How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


How do you Replace the ignition switch on a 1967 ford mustang?

AverageJoeResto.com has a How to article and video on removing the ignition switch How To Remove a Mustang Ignition Switch, it's actually pretty easy.


How do you change the key cylinder of the ignition switch in a 1991 acura legend?

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.