answersLogoWhite

0


Best Answer

Should be able to put down the tail gate and get to the screws that hold the lights on.

User Avatar

Wiki User

18y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove taillight assembly on a 2002 Dodge 2500?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you remove a engine on a 2002 dodge caravan?

The engine and transmission are removed out the bottom as an assembly.


Where is the horn on a 2002 Dodge neon located?

it is behind the passenger side headlight assembly. you will have to remove the headlight assembly to replace it.


How do you remove taillight cover on 2002 Ford Focus?

From the inside.


How do change a tail light on a dodge truck?

i have a 2002 dodge truck and this is how it is done; 1) lower the tailgate 2) There are 2 "torx" screws holding the housing on, remove them 3) The wire that leads to the bulb mount must be removed, there is a red lock on it, slide the lock to the left (from the top) and then remove the taillight assembly. 4) there are 4 Phillips head screws holding the light bulb mount, remove them and pull the mount from the lens assembly 5) replace bulbs 6) installation is the reverse of the dis-assembly. Have fun !!!


How do you remove the tail light assembly after removing the 2 bolts of a 2004 Toyota Sienna LE?

There is a pin in the taillight that needs to be pulled straight to the side. Do not leverage it or the taillight might crack. My 2002 Sienna has 2 pins. By pulling the taillight assembly straight out sideways (perpendicular to the side the car), with a little gentle leverage from above and below, it popped out nicely. Be careful and gentle.


Does 2002 dodge 1500 have circuit board in the taillight?

yes the taillight does in fact have a cicuit board. Once you take off the two bolts to remove the entire fixture the circuit board is the long plastic piece with the 4 screws holding in your 3 light bulbs


How do you change a taillight in a 2002 Nissan Frontier?

I believe you have to unscrew a couple bolts on the inside of the truck bed to get the taillight assembly off the truck then you can unscrew the light sockets and replace the burnt out bulb


How do you remove rear brake rotors on 2002 1500 dodge ram?

Remove wheelsRemove caliper mounting boltsSilide caliper off rotorRotor should slide of hub assembly


How do you replace brake light in a 2002 Jeep Liberty Sport?

Changing taillight assembly Jeep libertyI copied and pasted this from another blog.....it works perfectly!!!!For the drivers side taillight assembly remove the two screws on the side of taillight assembly. You need a special star screw driver (called "Torx", the come in different sizes). Don't strip the screws. If you do you will be in a world of hurt trying to remove these screws. You have to swing the tailgate open to see the screws. Once those screws are removed you have to pry the taillight assembly from the vehicle. Pry it straight out using a couple of large screw drivers as pry bars. Be careful not to scratch the paint. There are two plastic shafts that clip into the body. They run along the outside edge of the light assembly. Apply steady pressure with the pry until they come loose. It will take some force to break them free. Do not try to pull the assembly out with your hands from outside the vehicle as you will probably break the assembly.


How do you change rear turn signal bulb in a dodge Dakota 2002?

on all dodge trucks the way you change the bulbs is simply unscerew the tail light assembly and remove it from the rear of the vehicle and you will see your lightbulb fittings right on the back of the light assembly


How do you change taillight on a 2002 dodge ram 1500 pickup?

You Need A Special Tool, Which You Can Buy At AutoZone Or Something. You Open The Tail Gate, Then You Use The Special Tool To Unscrew the Screws And The Taillight Comes out.


How do I change the front rotors on a 2002 Dodge Intrepid?

Remove wheelsRemove caliper mounting boltsSlide caliper off rotorRotor should peel off hub assembly