Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.
Remove the wiring harness from the back of your 1995 Chevy Lumina front wiper motor. Remove the traveling arm linkage from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new front wiper motor.
You will have to remove the wiper arms, then remove the cowl, and then the wiper motor.
Remove the wiper arm from the wiper motor. Remove the wiring harness from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
Remove the wiring harness from the wiper motor. Remove the windshield wiper arm from the wiper motor. Remove the wiper motor retaining screws. Reverse the process to install the new wiper motor.
it is in front of the driver side under plastic scuttle panel where wiper arm bolted.. lift off cover and remove plastic insert, wiper motor is in front of you now..
Remove the wiper arm from the wiper motor. Remove the wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
Remove the rear wiper arm from the wiper motor. Remove the wiring harness from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
# Remove the windshield wiper arms # Remove the cowl cover # Disconnect the electrical connector from the wiper motor # Detach the wiper motor/linkage assembly from the cowl # Remove the wiper motor retaining bolts and remove the motor
* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor
Remove the wiper arm from your 1999 Oldsmobile Cutlass wiper motor. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
Remove the 2005 Honda Odyssey rear wiper arm from the wiper motor. Remove the wiring harness from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.
Remove the wiring harness from the wiper motor. Remove the wiper arm linkage. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.