0
Add your answer:
Earn +20 pts
What is the rear speaker size for a 2001 Oldsmobile intrigue?
6x9
Where does the Oldsmobile intrigue 1998 have the antenna?
The Antenna is built into the rear window.
How do you you remove the metal piece from a Lincoln town car rear view mirror to reglue the mirror up?
It slides in the direction of the smaller end. Be sure and glue the small end up, then slide the mirror back on.
How do you disassemble the metal bracket on the rear view mirror on an 2000 Oldsmobile Intrigue to glue to windshield?
I have a 1999 Oldsmobile Intrigue. The rearview mirror on my car has twin maplights, and on the back it says "Donnelly IE 8012001". I'm guessing the 2000 Intrigue uses the same parts. I just re-glued my mirror to the windshield after it fell off. Some other cars use a screw to attach the button to the mirror, but this mirror does not. Instead, I used a flat-head screwdriver to pry the button out of the mirror -- be careful to not to hurt yourself or the mirror. After prying the button out, I studied the mirror, and there doesn't appear to be any other way to remove the button. When gluing the button to the windshield, be careful to figure out which side and orientation the button needs to face before gluing it to the windshield.
How Much will it cost to replace the rear bumper cover on an Oldsmobile Intrigue?
The average cost for the part to replace the rear bumper cover on an Oldsmobile Intrigue varies between $88.00 and $124.00, depending on the year. The labor cost to replace the rear bumper will vary between $75.00 and $150.00 depending on the repair shop.
Replacing rear wheel bearings on olds intrigue?
The Oldsmobile Intrigue has rear wheel bearings that sometimes become faulty. It is possible to replace them by removing the old bearings and installing new or refurbished ones in their place.
How do you install a rear view mirror on a 1996 Oldsmobile Cutlass Supreme?
go to the parts store and get a rear view mirror mounting kit and follow the instructions to a T.
Where is the oil drain plug on a 1999 Oldsmobile intrigue?
Towards the bottom of the oil pan, facing towards the rear of the vehicle.
How do you get the clip off of the rear view mirror so you can reglue to the window of a 1998 Chevy lumina?
If by clip you mean the "shoe" that is the shiney square piece of metal that is in the mirror holder it slides out of the holder with prying by a screwdriver. Be careful not to hurt yourself.
Where is the fuel filter located on a Oldsmobile intrigue?
It in under the driver side rear door, about six inches in. Next to the fuel tank.
How do you disassemble the inside rear view mirror mount on a 1998 intrigue?
I have a 1999 Oldsmobile Intrigue. The rearview mirror on my car has twin maplights, and on the back it says "Donnelly IE 8012001". I'm guessing the 1998 Intrigue uses the same parts. I just re-glued my mirror to the windshield after it fell off. Some other cars use a screw to attach the button to the mirror, but this mirror does not. Instead, I used a flat-head screwdriver to pry the button out of the mirror -- be careful to not to hurt yourself or the mirror. After prying the button out, I studied the mirror, and there doesn't appear to be any other way to remove the button. When gluing the button to the windshield, be careful to figure out which side and orientation the button needs to face before gluing it to the windshield.
How do you replace a rear view mirror in an 1999 Intrigue can't get the button off the mirror?
I have a 1999 Oldsmobile Intrigue. The rearview mirror on my car has twin maplights, and on the back it says "Donnelly IE 8012001". I just re-glued my mirror to the windshield after it fell off. Some other cars use a screw to attach the button to the mirror, but this mirror does not. Instead, I used a flat-head screwdriver to pry the button out of the mirror -- be careful to not to hurt yourself or the mirror. After prying the button out, I studied the mirror, and there doesn't appear to be any other way to remove the button. When gluing the button to the windshield, be careful to figure out which side and orientation the button needs to face before gluing it to the windshield.
